Adjusting the blades on a reel mower is a routine maintenance task that keeps your lawn looking clean and your mower cutting efficiently. Over time, the reel and bedknife can become misaligned, leading to a dull, ragged cut or a mower that is hard to push. This guide walks you through the process of adjusting the reel-to-bedknife contact, which is the core of a reel mower’s cutting action. Before you start, make sure you have a clean, flat workspace and that the mower is on a stable surface. You’ll also want to have the owner’s manual for your specific model on hand, as the exact adjustment points may vary slightly.
What You’ll Need
- Adjustable wrench or socket set (sizes vary by model)
- Screwdriver (flathead or Phillips, depending on your mower)
- Feeler gauge (optional, but helpful for precise adjustment)
- Light machine oil or reel mower lubricant
- Clean rag
- Gloves (to protect your hands)
Step-by-Step
- Clean the mower. Remove any grass clippings, dirt, or debris from the reel, bedknife, and the adjustment areas. A clean mower makes it easier to see and access the parts.
- Locate the adjustment points. On most reel mowers, there are two adjustment screws or nuts on each side of the mower, near the bedknife (the stationary blade at the bottom). These control the reel’s position relative to the bedknife. Some mowers have eccentric bolts or a single adjustment per side.
- Loosen the locknuts. Using your wrench, loosen the locknuts on the adjustment screws. Do not remove them; just loosen them enough so you can turn the screws.
- Set the initial gap. If you’re using a feeler gauge, insert a thin gauge (about the thickness of a piece of paper) between the reel blades and the bedknife. If not, you’ll adjust by feel. The goal is to have the reel lightly touch the bedknife at the point of closest contact, but not so tight that it binds.
- Adjust the reel. Turn the adjustment screws on both sides evenly. On most mowers, turning the screws clockwise moves the reel closer to the bedknife, and counterclockwise moves it away. Make small adjustments—a quarter turn at a time—and alternate between sides to keep the reel parallel.
- Check the contact. After adjusting, spin the reel by hand. It should turn smoothly with a slight resistance at the point where the reel blade meets the bedknife. You should hear a light, even ‘tick’ as each blade passes the bedknife. If the reel is hard to turn or makes a grinding sound, you’ve adjusted too tight.
- Tighten the locknuts. Once the adjustment feels right, hold the adjustment screws in place and tighten the locknuts securely. Be careful not to overtighten, as this can strip the threads.
- Test the cut. Push the mower on a small patch of grass (or a piece of paper) to see if it cuts cleanly. The paper test is a quick way to check: if the mower cuts a clean slice through a piece of paper held in front of the reel, the blades are sharp and properly adjusted. If it tears or misses, you may need to adjust again or sharpen the blades.
- Lubricate. Apply a few drops of light oil to the reel bearings and the adjustment points to keep everything moving smoothly.
Common Mistakes
- Over-tightening. Setting the reel too tight against the bedknife is the most common error. This causes excessive friction, makes the mower very hard to push, and can damage the blades or bearings.
- Adjusting only one side. If you adjust only one side, the reel becomes misaligned, leading to an uneven cut and premature wear.
- Skipping the cleaning step. Grass and dirt can hide the adjustment points and interfere with the mechanism, making it hard to get an accurate adjustment.
- Using the wrong tools. Using pliers or an ill-fitting wrench can round off the nuts and make future adjustments difficult.
Tips
- Adjust in small increments. A quarter turn can make a noticeable difference. Take your time and check frequently.
- Use the paper test. A simple piece of paper is a great diagnostic tool. If the mower can’t cut paper cleanly, the blades are likely dull or the gap is too wide.
- Check the reel for straightness. If you notice a wobble or a varying gap along the length of the reel, the reel may be bent. In that case, you may need to have it professionally straightened or replaced.
- Keep the bedknife sharp. The bedknife can be sharpened with a sharpening stone or a file. A dull bedknife will not cut well even with a properly adjusted reel.
- Follow the manufacturer’s instructions. Some mowers have specific adjustment procedures or require special tools. Always consult your owner’s manual.
Troubleshooting
- Mower is still hard to push after adjusting. If the reel is not binding, the issue may be in the wheels or the axle. Check for debris or lack of lubrication. Also, ensure the cutting height is set appropriately for your grass type.
- Reel doesn’t touch the bedknife at all. This usually means the adjustment screws are too loose or the reel is worn. If the reel is worn, you may need to replace it or have it sharpened.
- Uneven cut across the width. This suggests the reel is not parallel to the bedknife. Re-adjust, making sure to turn both sides equally and check with a feeler gauge at both ends.
- Grinding or clicking noise. A clicking noise is normal if it’s a light tick. A loud grinding sound means the reel is too tight or there’s debris stuck between the blades. Loosen the adjustment and clean the mower.
- Blades are dull. If the blades are properly adjusted but still tear the grass, they need sharpening. You can do this with a reel mower sharpening kit or take it to a professional.
Frequently Asked Questions
- How often should I adjust the blades? It depends on usage and conditions. A good rule is to check the adjustment at the start of each mowing season and whenever you notice a decline in cut quality.
- Can I adjust the blades without removing the reel? Yes, in most cases you can adjust the reel-to-bedknife clearance without removing the reel. The adjustment points are usually accessible from the outside.
- What if my mower has a fixed bedknife? Some cheaper reel mowers have a fixed bedknife that cannot be adjusted. In that case, you may only be able to adjust the reel by moving the entire reel assembly, or you may need to replace the bedknife if it’s worn.
- How do I know if my reel is too tight? If the reel is difficult to spin by hand or makes a high-pitched squealing sound, it’s too tight. You should be able to spin it with a slight resistance.
- Is it necessary to use a feeler gauge? No, but it helps for precision. Many experienced users can adjust by feel alone. The paper test is a good substitute.
- Can I sharpen the blades myself? Yes, with a sharpening kit or a file, but it’s a delicate process. If you’re not confident, it’s best to have a professional do it.