Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

Accent Wall with Cedar Plank Fencing: Step-by-Step

Turning a plain wall into a warm, textured focal point is easier than you think when you use cedar plank fencing. These pre-cut, weather-resistant boards are affordable, readily available at home improvement stores, and bring a natural, rustic charm to any room. This guide walks you through the entire process, from gathering materials to troubleshooting common issues, so you can achieve a professional-looking accent wall in a weekend.

What You’ll Need

  • Cedar fence pickets (the number depends on your wall size; measure the width and height first)
  • Stud finder
  • Measuring tape
  • Level (a long one is best)
  • Pencil
  • Circular saw or miter saw (for cutting boards to length)
  • Sandpaper (medium grit)
  • Wood filler (if you want to hide nail holes)
  • Paint or stain (optional, if you want to change the color)
  • Primer (if painting)
  • Construction adhesive (heavy-duty, for paneling)
  • Nail gun or hammer and finishing nails
  • Wood shims (for leveling)
  • Caulk and caulk gun (for gaps at edges)
  • Safety glasses and dust mask

Step-by-Step

  1. Prepare the Wall: Remove any wall decor, outlet covers, and switch plates. Clean the wall surface with a damp cloth to remove dust and grease. If there are any large holes or cracks, fill them with spackle and let dry. Sand smooth.
  2. Acclimate the Cedar: Bring the cedar planks into the room where you’ll install them and let them sit for a couple of days. This allows the wood to adjust to the room’s humidity, reducing the chance of warping or shrinking after installation.
  3. Measure and Plan: Measure the height and width of your wall. Decide on the spacing between planks – a common choice is a small gap (about the width of a nail) for a modern look, or butt them tightly for a seamless appearance. Calculate how many planks you need by dividing the wall width by the plank width plus spacing. It’s wise to buy an extra few planks to account for cuts and mistakes.
  4. Find the Studs: Use a stud finder to locate the wall studs. Mark them lightly with a pencil. You’ll want to nail into studs for a secure hold, especially if the wall is drywall.
  5. Cut the First Plank: Measure the height of the wall from floor to ceiling. Cut your first plank to that length using a circular saw. If your ceiling or floor is uneven, you can scribe the plank to fit – hold it in place and mark the contour, then cut along the line.
  6. Apply Adhesive: Run a zigzag bead of construction adhesive along the back of the plank. This will provide a strong bond and help prevent the plank from bowing.
  7. Install the First Plank: Press the plank firmly against the wall in one corner. Use a level to ensure it’s perfectly vertical. If it’s not, use wood shims behind the plank to adjust. Nail the plank into the studs using a nail gun or hammer and finishing nails. Place nails near the top, middle, and bottom, and along the edges where they’ll be covered by the next plank.
  8. Continue Installing Planks: For the next plank, use a spacer (like a small piece of wood or a nail) to maintain an even gap. Apply adhesive, position, level, and nail. Repeat this process across the wall. Check for level frequently – walls are often not perfectly straight, so you may need to shim the planks to keep them plumb.
  9. Cut Around Obstacles: When you reach outlets or switches, measure the location and cut the plank accordingly. Use a jigsaw for intricate cuts. Always turn off the power to the circuit before cutting near electrical boxes.
  10. Finish the Last Plank: The final plank will likely need to be ripped (cut lengthwise) to fit the remaining space. Measure the gap, subtract the spacing, and cut the plank to width. Install it as before.
  11. Fill and Sand (Optional): If you want a cleaner look, fill the nail holes with wood filler that matches the cedar tone. Once dry, sand lightly with fine-grit sandpaper. If you’re painting or staining, now is the time to apply a primer (if painting) and your chosen finish.
  12. Caulk the Edges: Apply a thin bead of caulk along the top, bottom, and side edges where the planks meet the ceiling, floor, and adjacent walls. Smooth with a wet finger. This gives a professional, finished appearance.

Common Mistakes

  • Skipping the acclimation period: Installing planks that haven’t adjusted to the room’s humidity can lead to gaps or warping later.
  • Not using a level: Even a slight tilt will be noticeable across a whole wall. Always check each plank.
  • Not finding studs: Nailing only into drywall may not hold the weight of the planks, especially if they are heavy or the adhesive fails.
  • Ignoring uneven walls: Walls are rarely perfectly flat. If you don’t shim, the planks will follow the curve, creating a wavy appearance.
  • Cutting all planks to the same length: Floors and ceilings are often not level. Measure each plank individually to avoid gaps at the top or bottom.
  • Forgetting to turn off power: Cutting near outlets without shutting off the circuit is a serious safety hazard.

Tips

  • Choose your planks carefully: Look for boards that are straight and free of large knots. The more uniform they are, the easier the installation.
  • Pre-sand the planks: Cedar is often rough. A quick sanding with medium grit will make the surface smoother and more pleasant to touch.
  • Use a spacer: A simple piece of scrap wood cut to the desired gap width will make spacing consistent and fast.
  • Consider a dark stain: A dark walnut or ebony stain can give the cedar a dramatic, modern look. Test on a scrap piece first.
  • Work with a helper: Planks can be long and awkward. A second pair of hands makes positioning and leveling much easier.
  • Seal the wood: If you want to keep the natural cedar color, apply a clear matte sealer to protect it from moisture and UV light.

Troubleshooting

  • Planks are warping or bowing: This can happen if the wood wasn’t acclimated or if the adhesive didn’t bond well. Remove the affected plank, apply more adhesive, and press firmly. You can also add extra nails to hold it flat.
  • Gaps at the top or bottom: If your floor or ceiling is uneven, you’ll have gaps. You can cut a thin piece of trim (like quarter-round) to cover the gap, or use caulk to fill it if it’s small.
  • Planks are not staying flush to the wall: This usually means the wall is bowed. Use shims behind the plank to bring it flush, then nail through the shim. The shim will be hidden by the next plank.
  • Adhesive is oozing out: Wipe it off immediately with a damp cloth. If it dries, you can carefully scrape it off with a putty knife.
  • Nail holes are visible: If you didn’t fill them, you can use a wood filler that matches the cedar color. Or, you can intentionally use a contrasting filler for a rustic look.
  • The last plank doesn’t fit: If your measurement was off, you may need to rip the plank to width. If you don’t have a table saw, you can use a circular saw with a straightedge guide.

Frequently Asked Questions

  • Can I install cedar planks directly over drywall? Yes, that’s the most common method. The planks are lightweight enough that with adhesive and nails into studs, they will hold securely.
  • Do I need to remove the baseboard? You can leave it on and butt the planks against it, or you can remove it and install the planks flush to the floor. Removing it gives a cleaner look but adds work. If you leave it, you’ll need to caulk the seam.
  • How do I cut around outlets? Turn off the power, measure the outlet’s position and size, and mark it on the plank. Use a jigsaw to cut the hole. You can also use a hole saw for the top and bottom of the outlet and then connect with a straight cut.
  • Should I seal the cedar? Sealing is optional. If you like the natural color and want to protect it from moisture, apply a clear sealer. If you want to paint or stain, you don’t need a separate sealer.
  • Can I use this on a ceiling? Yes, the same technique works for ceilings, but it’s more physically demanding. You’ll definitely need a helper and possibly a nail gun with a longer reach.
  • How do I clean the wall afterward? Use a soft brush attachment on a vacuum or a slightly damp microfiber cloth. Avoid harsh chemicals or excessive water, as they can damage the wood.
Accent Wall with Cedar Plank Fencing: Step-by-Step
Scroll to top