High winds can lift, tear, or peel back roofing materials even on a well-maintained home. Catching and fixing this damage quickly is the difference between a simple repair and a costly interior leak. This guide walks you through a safe ground-level inspection, a cautious roof-top check, and the most common DIY fixes for wind-damaged asphalt shingles. Before you start, confirm the weather is calm and dry, and if the roof is steep, more than two stories high, or you feel unsteady, stop and call a professional roofer.
What You’ll Need
- Binoculars (for ground inspection)
- Ladder (stable, extendable, rated for your weight)
- Safety harness and rope (if working on a sloped roof)
- Roofing nails (galvanized, correct length for your deck)
- Hammer or nail gun
- Roofing cement or sealant
- Putty knife or trowel
- Replacement shingles (matching color and style)
- Utility knife
- Flat pry bar (for lifting shingles)
- Chalk line (for aligning repairs)
- Work gloves and non-slip shoes
Step-by-Step
- Start with a ground inspection. Walk around your home and use binoculars to scan the roof. Look for lifted, curled, or missing shingles, exposed nail heads, and any debris like branches or granules in the gutters. Also check the ground for shingle pieces that blew off.
- Check the attic for leaks. Go inside and look at the underside of the roof deck. Use a flashlight to spot water stains, dark streaks, or daylight coming through gaps. Mark any wet or stained areas with chalk so you can find them from outside.
- Set up your ladder safely. Place the ladder on firm, level ground at a safe angle (about one foot out for every four feet up). Have someone hold the base, and extend it at least three feet above the roof edge. Never lean sideways to reach.
- Inspect the roof surface carefully. Once on the roof, walk only in the valleys or on the lower half of shingles to avoid damage. Look for shingles that are lifted at the corners, have torn tabs, or are missing entirely. Check flashings around chimneys, vents, and skylights for lifted seams or pulled nails.
- Re-secure lifted shingles. For a shingle that is curled but intact, apply a generous dab of roofing cement under the lifted edge with a putty knife. Press the shingle flat and hold for a few seconds. If the shingle has exposed nails, lift it gently, seal the nail heads with cement, and press it back down.
- Replace torn or missing shingles. Use a flat pry bar to lift the shingle above the damaged one. Remove the nails holding the damaged shingle in place, then slide the old shingle out. Slip the new shingle into position, align it with the course, and nail it just below the adhesive strip. Seal the nail heads with roofing cement.
- Seal any exposed nail heads. Wind often pops nails loose. If you see any nail heads poking up, drive them back down and cover each with a dab of roofing cement. This prevents water from seeping in around the fastener.
- Repair flashing damage. If flashing around a chimney or vent is loose, re-secure it with roofing nails and seal the edges with a high-quality roofing sealant. Never use caulk meant for windows; it will not hold up to sun and rain.
- Clear debris from valleys and gutters. Wind-blown leaves and twigs trap moisture. Sweep or brush debris off the roof valleys and out of the gutters to keep water flowing freely.
- Do a final check. Walk the roof one more time, looking for anything you missed. Then go back inside and re-check the attic for new stains or drafts. If you made a repair, monitor that spot after the next rain.
Common Mistakes
- Walking on shingles in cold weather. Shingles become brittle and crack easily when temperatures drop. Do repairs only when it is warm enough for the shingles to be flexible.
- Using too few nails. A shingle that is only nailed at the top edge will lift again. Always use the correct number of nails per shingle, typically four to six, placed in the designated nailing zone.
- Over-nailing or driving nails too deep. Nails that are driven flush or below the surface can puncture the shingle above and create a leak. Nail heads should sit flush with the shingle surface, not sunken.
- Sealing shingles without cleaning the area. Dirt and old granules prevent the cement from bonding. Wipe the area clean with a dry cloth before applying any sealant.
- Ignoring the ridge caps. Ridge shingles take the brunt of wind. Check the peak of your roof carefully; a missing ridge cap is a common source of leaks.
Tips
- Match the shingle color. Buy a bundle of the same brand and color if possible. If you cannot match exactly, use shingles from an inconspicuous area, like a garage, and replace those with a close match.
- Work in pairs. Have a helper hand you tools and watch your ladder. They can also be the one to go inside and check for leaks while you are on the roof.
- Take photos before you start. Document the damage for your insurance claim before you make any repairs. Most policies cover wind damage, but you need evidence.
- Use a chalk line for straight courses. When replacing a row of shingles, snap a chalk line to keep the new course straight and aligned with the existing rows.
- Check the roof deck. If a shingle was torn off completely, inspect the wood underneath. If the deck is soft, rotted, or water-stained, you may need to replace a section of plywood before re-shingling.
Troubleshooting
- The leak is still there after the repair. Water can travel along the roof deck before dripping. Your repair may be correct, but the leak point is higher up. Check the entire slope above the stain, not just the spot directly above the ceiling stain.
- Shingles are cracking as you work. Stop immediately. The shingles are too cold or too old. Wait for a warmer day, or if the shingles are brittle due to age, it may be time for a full re-roof.
- You cannot find the source of the leak. Use a garden hose to simulate rain. Have a helper spray water on the roof section by section while you watch the attic for drips. Start low and work your way up.
- Mold or dark stains appear after fixing. This usually means moisture is trapped. Check that your repair is fully sealed and that the area has proper ventilation. If the stain grows, you may have a hidden leak from a nail pop or a small crack.
- The repair fails within a few weeks. The cement may have been applied to a wet or dirty surface, or the shingle was not pressed down long enough. Re-clean the area, let it dry completely, and reapply a thicker layer of cement.
Frequently Asked Questions
Q: Can I repair wind damage myself, or should I hire a roofer?
A: Minor issues like lifted shingles or a few missing nails are DIY-friendly if you are comfortable on a ladder. If the damage covers a large area, involves torn flashing, or the roof is steep, hire a professional.
Q: How soon after a storm should I make repairs?
A: As soon as the weather is safe and dry. Even a small lifted shingle can let water in during the next rain. Temporary tarps can protect the roof until you are able to do a permanent fix.
Q: Will my insurance cover wind damage to the roof?
A: Most standard homeowners policies cover wind damage, but deductibles and coverage limits vary. Document the damage with photos and contact your insurer before starting major repairs. Minor DIY fixes are usually not worth filing a claim for.
Q: How do I know if the shingles are too old to repair?
A: If shingles are brittle, cracked, or losing granules heavily, they are near the end of their life. Repairing individual spots will only delay the inevitable. A roofing professional can assess the overall condition.
Q: What is the best sealant for roof repairs?
A: Use a roofing cement or asphalt-based sealant designed for shingle repairs. Avoid silicone or general-purpose caulk, which does not adhere well to asphalt and can degrade in sunlight.
Q: Can I walk on my roof to inspect it?
A: Yes, if it is dry, not too steep, and you have proper footwear and a safety harness. Walking on a wet or cold roof is dangerous and can damage the shingles. When in doubt, inspect from the ground with binoculars.