Fixing a brick planter attached to your house not only restores its appearance but also prevents water from seeping into your foundation or basement. Over time, freeze-thaw cycles, settling, and plant roots can crack mortar and loosen bricks. This guide walks you through repairing a typical brick planter, from assessing the damage to repointing and sealing. Before you start, check that the planter is structurally sound—if it leans away from the house or has large gaps, you may need to consult a professional. Also, ensure the area is dry and that you have a day or two of clear weather for the mortar to cure.
What You’ll Need
- Safety glasses and work gloves
- Chisel or masonry chisel
- Hammer (or small sledgehammer)
- Wire brush
- Mortar mix (type N or S, depending on your climate)
- Water and a spray bottle
- Mortar bag or trowel
- Jointing tool or a piece of pipe
- Broom or brush for cleanup
- Bucket for mixing
- Optional: masonry sealer and a brush
Step-by-Step
- Assess the damage. Look for loose bricks, crumbling mortar, and any cracks that extend into the house wall. If the planter is pulling away from the house, you may need to install metal ties—skip to troubleshooting if that’s the case. For now, focus on repointing and replacing damaged bricks.
- Remove loose mortar. Use a chisel and hammer to carefully chip out any loose or crumbling mortar from the joints. Work from the top down. Remove mortar to a depth of about twice the width of the joint, but don’t go deeper than the brick itself. Be gentle to avoid damaging the bricks.
- Clean the joints. Use a wire brush to sweep out all dust and debris from the joints. Then rinse the area with a hose or spray bottle to remove fine dust. Let it dry completely—mortar won’t adhere well to damp surfaces.
- Replace any damaged bricks. If a brick is cracked or broken, chisel it out carefully. Clean the opening, then mix a small batch of mortar. Butter the new brick with mortar on all sides that will touch existing brick, then press it into place. Use a level to ensure it’s flush with the surrounding bricks. Allow it to set for a few hours.
- Mix fresh mortar. Follow the manufacturer’s instructions on the bag. Typically, you’ll add water and mix to a consistency like thick peanut butter. Mix only as much as you can use in about half an hour, as mortar sets quickly.
- Apply the mortar. Use a trowel to push mortar into the vertical joints first, then the horizontal ones. For deeper joints, use a mortar bag—it works like a pastry bag and lets you fill the joint fully. Overfill slightly, as mortar will shrink as it cures.
- Tool the joints. After the mortar has firmed up (about when your fingerprint barely makes an impression), use a jointing tool or a piece of pipe to press the mortar into a smooth, concave shape. This helps shed water and gives a professional look.
- Clean the bricks. Before the mortar hardens completely, use a dry brush to wipe any smears off the brick faces. If you wait too long, the mortar will be hard to remove without damaging the brick.
- Let it cure. Keep the repaired area slightly damp for a few days. Mist it with water once or twice a day, especially in hot, dry weather. This slow curing makes the mortar stronger.
- Seal the planter (optional). Once the mortar has cured for at least a week, apply a masonry sealer to the entire planter. This helps prevent water absorption and future freeze-thaw damage. Follow the sealer’s instructions for application and drying time.
Common Mistakes
- Using the wrong mortar. Portland cement-based mortar is too hard and will crack the bricks. Use a mortar mix that matches the original—usually type N for above-grade work. If you’re unsure, take a sample to a masonry supply store.
- Skipping the cleaning step. Dust and debris prevent the new mortar from bonding. Always brush and rinse the joints thoroughly.
- Applying mortar to a wet surface. While you want the bricks slightly damp, they should not be soaking wet. Wait until the surface is just barely moist.
- Overfilling the joints. Excess mortar can smear and be hard to clean. Overfill slightly, but tool it back to a neat finish.
- Not letting it cure. If you disturb the mortar too soon, it can crack or pull away. Be patient and keep it damp for several days.
Tips
- Work in small sections so the mortar doesn’t set before you finish tooling.
- Use a tarp to protect the ground and any nearby plants from mortar drips.
- If the planter is tall, work from a sturdy ladder—never overreach.
- Consider adding a waterproof membrane between the planter and the house wall if there isn’t one. This prevents moisture from wicking into your home’s structure.
- For a better match, test the mortar color on a hidden spot and let it dry—mortar color changes as it cures.
Troubleshooting
- Mortar keeps crumbling after repair. This usually means the mix was too dry, the surface was dusty, or the mortar is too weak. Chip out the failed areas and redo them, making sure the joints are clean and slightly damp.
- The planter is pulling away from the house. This is a structural issue. You’ll need to install metal wall ties that connect the planter to the house’s foundation. This is a more involved job—if you’re not comfortable, call a mason.
- Water is seeping into the basement. Check for cracks in the planter’s base or where it meets the house. Seal any gaps with a polyurethane caulk designed for masonry. If the problem persists, you may need to install a drainage system behind the planter.
- Bricks are efflorescing (white powder). This is salt from the mortar or bricks. Clean with a stiff brush and water, then seal the planter to reduce moisture movement.
- The mortar sets too fast. On hot days, mortar can stiffen quickly. Work in the shade, mix smaller batches, and keep the area misted.
Frequently Asked Questions
- Can I use regular cement instead of mortar? No. Cement is too hard and will crack the bricks. Use a masonry mortar mix, which is softer and more flexible.
- How long does mortar take to dry? It sets in a few hours, but it takes several days to cure fully. Keep it damp for at least a few days to ensure strength.
- Do I need to seal the planter? Sealing is optional but recommended, especially in cold climates. It helps prevent water absorption and freeze-thaw damage.
- Can I plant directly in the repaired planter? Yes, but consider adding a liner or waterproof membrane to protect the brick from soil moisture and roots.
- What if the planter is very large or tall? For large repairs or if the planter is more than a few feet high, it’s safer to hire a professional. Structural issues can be dangerous.
- Why does the mortar crack every winter? This is likely due to water getting into the joints and freezing. Ensure good drainage, use a flexible sealer, and repair cracks promptly.
Fix a Brick Planter Attached to Your House