Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

How to Fix a Cord Chewed by Your Pet

Pets, especially puppies and kittens, love to chew on cords. It’s a common problem that can be frustrating, expensive, and dangerous. A chewed cord can cause a short circuit, a fire hazard, or even an electrical shock to your pet. This guide will walk you through the steps to safely repair a chewed cord, whether the damage is minor or severe. Before you begin, always unplug the cord from the wall and assess the damage. If the cord is completely severed or you see exposed copper wires, you’ll need to replace the entire cord or call a professional. For minor damage, a few simple tools can restore the cord to working order.

What You’ll Need

  • Wire cutters or a sharp utility knife
  • Electrical tape (rated for the cord’s voltage)
  • Heat-shrink tubing (optional but recommended)
  • A heat source (lighter or heat gun) for heat-shrink tubing
  • Wire strippers (or a knife if you’re careful)
  • Electrical wire connectors (butt splices) or a soldering iron and solder
  • Multimeter (optional, for testing)

Step-by-Step

  1. Unplug the cord. Never work on a cord that is plugged in. Even if the cord looks intact, there could be exposed wires inside.
  2. Inspect the damage. Look for cuts, nicks, or exposed wires. If the outer insulation is only slightly damaged, you can simply wrap it with electrical tape. If the inner wires are damaged or the cord is fully severed, proceed to the next steps.
  3. Cut out the damaged section. Use wire cutters to remove the chewed area. Make a clean cut on either side of the damage. If the cord is only nicked, you can cut just the damaged portion. If the cord is severed, you’ll need to cut back to the point where the insulation is intact.
  4. Strip the wires. Use wire strippers to remove about a half-inch of insulation from each end of the wires. You’ll see two or three inner wires (usually black, white, and green or bare copper). Strip each of these inner wires as well.
  5. Twist or solder the wires together. Match the colors: black to black, white to white, and green/bare to green/bare. Twist the matching wires together securely. If you have a soldering iron, solder each connection for a stronger bond.
  6. Cover each connection. Wrap each individual wire connection with electrical tape. This prevents short circuits between the wires. If you’re using heat-shrink tubing, slide a piece over each wire before soldering, then shrink it over the connection with your heat source.
  7. Wrap the entire repair. Once all wires are individually covered, wrap the whole area with electrical tape, overlapping it as you go. This restores the outer insulation and protects the repair.
  8. Test the cord. Before plugging it in, check your work with a multimeter if you have one. Set it to continuity mode and test the plug prongs to ensure there’s a continuous path. If you don’t have a multimeter, plug the cord in and test the device—but be cautious. If the device doesn’t work, unplug it immediately and re-check your connections.

Common Mistakes

  • Not unplugging first. This is the most dangerous mistake. Always unplug the cord before touching it.
  • Using too much electrical tape. While tape is good, over-wrapping can make the cord stiff and prone to bending damage. Use just enough to cover the repair snugly.
  • Mixing up wire colors. If you connect the hot wire to the neutral, the device may not work or could be a shock hazard. Always match colors.
  • Leaving exposed copper. Even a tiny bit of exposed wire can cause a short circuit. Make sure every connection is fully covered.
  • Repairing a cord that’s too damaged. If the cord is chewed in multiple places or the damage is extensive, a repair isn’t safe. Replace the cord entirely.

Tips

  • Use heat-shrink tubing instead of tape. It provides a more durable, professional-looking repair.
  • Apply a bitter apple spray to the cord after repair. This deters your pet from chewing again.
  • Use cord protectors. You can buy flexible plastic tubing that wraps around the cord, or you can use a split loom. This is a great preventive measure.
  • Keep cords out of reach. Tuck cords behind furniture or use cable clips to secure them to walls or baseboards.
  • Provide alternatives. Give your pet plenty of chew toys to redirect their chewing instinct.

Troubleshooting

If the repair doesn’t work, here’s what to check:

  • The device still doesn’t power on. Double-check your connections. Are the wires twisted tightly? Did you strip enough insulation? If you used a butt splice, make sure it’s crimped securely. If you soldered, check for cold solder joints (dull, not shiny).
  • The cord gets warm when plugged in. This is a sign of a poor connection. Unplug it immediately. The wires may not be making good contact, causing resistance and heat. Re-do the repair with a stronger connection.
  • The circuit breaker trips. This indicates a short circuit. There may be a stray wire touching another. Unplug the cord and inspect each connection carefully. Make sure the individual wires are not touching each other before you wrap the outer insulation.
  • You see sparks when plugging in. Stop! Do not plug it in again. The cord is unsafe. Cut the cord and replace it entirely.

Frequently Asked Questions

Can I just wrap electrical tape around a chewed cord?

Only if the outer insulation is slightly nicked and no inner wires are exposed. If you can see any copper wire, you must cut and re-splice the cord.

Is it safe to repair a cord that was chewed all the way through?

Yes, if you cut out the damaged section and splice the wires back together correctly. However, if the cord is damaged in multiple places, it’s safer to replace it.

What if my pet chewed the cord while it was plugged in?

Unplug it immediately and inspect for any signs of melting or burning. If the cord is hot, smells like burnt plastic, or has any blackened areas, replace it. Also, monitor your pet for any signs of injury, and consult a vet if you’re concerned.

How do I know if the cord is too damaged to repair?

If the cord is chewed in several places, if the damage is longer than a few inches, or if the inner wires are frayed or broken in multiple spots, it’s best to replace the entire cord. A repair that is too long will be weak and could fail.

Can I use duct tape instead of electrical tape?

No. Duct tape is not rated for electrical insulation and can conduct electricity when wet. Always use electrical tape or heat-shrink tubing.

How can I stop my pet from chewing cords again?

Use cord protectors, apply bitter apple spray to the repaired area, and provide plenty of chew toys. Also, supervise your pet and redirect their attention if they start to chew on a cord.

How to Fix a Cord Chewed by Your Pet
Scroll to top