Adding a valance over vertical blinds instantly softens the look of a window, hides the often-utilitarian headrail, and gives the room a more finished, layered appearance. The process is straightforward, but it does require some careful measuring and the right mounting hardware, especially because vertical blind headrails are typically mounted flush against the window frame or ceiling. This guide walks you through the entire process, from choosing the right valance to securing it without damaging your blinds.
What You’ll Need
- A valance (either a standard curtain valance or a cornice board)
- A curtain rod or a wooden mounting board (depending on the valance style)
- Mounting brackets and screws (included with most rods or purchased separately)
- A drill with drill bits and a screwdriver bit
- A stud finder (optional but helpful)
- A level
- A tape measure
- A pencil for marking
- Wall anchors (if not screwing into a stud)
- A stepladder (if the window is high)
Step-by-Step
- Measure the window and the blind headrail. Use a tape measure to get the exact width of the vertical blind headrail (the long, horizontal bar at the top). Also measure the depth from the wall to the front of the headrail, and the height from the top of the headrail to the ceiling. This tells you how much space you have to work with and what size valance will cover the hardware completely.
- Choose your valance style and mounting method. For vertical blinds, the two most common options are a traditional fabric valance on a curtain rod, or a rigid cornice board. A curtain rod valance is lighter and easier to install, but it will leave a gap between the rod and the headrail if the headrail protrudes far from the wall. A cornice board is a wooden box that wraps around the headrail, offering a cleaner, more custom look. Decide which suits your room and skill level.
- Determine the mounting location. Ideally, you want the valance to sit just above the blind headrail, covering it entirely. If you are using a curtain rod, the brackets should be installed on the wall or the window frame, a few inches above the headrail. If you are using a cornice board, you will typically mount it directly to the wall above the headrail, or to the ceiling if the headrail is ceiling-mounted. Mark the desired height with a pencil.
- Locate the studs (if possible). Use a stud finder to locate the wooden studs behind the drywall. Screwing into a stud provides the strongest hold, especially for a heavier cornice board. If no studs are available, you will need to use wall anchors rated for the weight of your valance. Mark the stud locations on the wall.
- Install the mounting brackets. Hold the bracket up to the wall at your marked height, ensuring it is level. Use a pencil to mark the screw holes. Drill pilot holes (a bit smaller than your screws) into the wall, then insert wall anchors if you are not hitting a stud. Screw the brackets into place, making sure they are level and aligned with each other.
- Attach the valance to the rod or board. If using a curtain rod, slide the valance onto the rod (most valances have a rod pocket or clip rings). If using a cornice board, you will typically attach the valance fabric to the board with a staple gun, or the board itself may be the valance (painted wood). Follow the manufacturer’s instructions for your specific valance.
- Hang the valance. Place the rod onto the installed brackets, or lift the cornice board and secure it to the wall brackets with screws. Ensure the valance sits straight and covers the headrail completely. Step back and check the alignment.
- Adjust and finalize. If the valance is too long, you may need to trim it (for fabric valances, hem it; for cornice boards, cut the board). If it is too short, you may need to lower the brackets. Once everything looks good, tighten all screws and enjoy your refreshed window.
Common Mistakes
- Not measuring the headrail depth. A common error is buying a valance that is too shallow to cover the blind’s headrail, leaving it sticking out from behind the fabric. Always measure the depth and compare it to the valance’s depth.
- Mounting the valance too high. If you mount the valance too far above the headrail, you will see a gap between the valance and the blinds, which looks unfinished. The valance should sit just above the headrail, ideally touching or nearly touching it.
- Screwing into drywall without anchors. A valance, especially a cornice board, can be surprisingly heavy. Screwing directly into drywall without anchors will likely result in the screws pulling out over time. Always use anchors or hit a stud.
- Ignoring the blind cord. Vertical blinds have a cord or chain that hangs down on one side. Make sure your valance installation doesn’t interfere with the cord’s movement, or you may have trouble opening and closing the blinds.
- Not using a level. An uneven valance is very noticeable. Always use a level when installing brackets to ensure a straight line.
Tips
- Consider a valance that matches the blind color. If you want a seamless look, choose a valance in a color close to the blind’s headrail. If you want contrast, go with a bold pattern.
- Use a tension rod for a temporary solution. If you are renting or want a no-drill option, a tension rod can work for a lightweight fabric valance, but it must be placed inside the window frame, which may not cover the headrail. This works best if the headrail is recessed.
- For a cornice board, use a staple gun for fabric. This gives a clean, professional finish without sewing. Pull the fabric tight and staple it to the back of the board.
- If the headrail is ceiling-mounted, mount the valance from the ceiling. This is often easier than trying to attach to the wall, and it creates a clean, floor-to-ceiling look.
- Take the valance down before cleaning the blinds. This prevents dust accumulation and makes cleaning easier.
Troubleshooting
- The valance doesn’t cover the headrail completely. If the headrail is deeper than the valance, you have a few options: lower the valance so it sits in front of the headrail (not above it), or add a small extension piece to the valance (for cornice boards). For fabric valances, you may need to use a wider rod or add a second layer of fabric.
- The valance is crooked. Check that the brackets are level and that the valance is hanging evenly. If using a rod, the rod may be bent—replace it. For cornice boards, check that the board itself is square.
- The valance falls down. This usually means the screws are not anchored properly. Remove the valance, install stronger wall anchors or screw into a stud, and rehang. If the drywall is damaged, you may need to patch it and move the brackets slightly.
- The blind cord is stuck. If the valance is pressing against the cord, move the valance slightly to one side, or adjust the cord guide on the headrail. Do not force the cord—this could damage the blind mechanism.
- The valance sags in the middle. This is common with long fabric valances on a rod. Install a center support bracket on the rod (most rods include one) to hold the middle up.
Frequently Asked Questions
Can I hang a valance without drilling holes? Yes, you can use a tension rod if the valance is lightweight and the window frame is deep enough. However, this method may not cover the headrail completely, and it is not as secure as a drilled installation.
What is the best type of valance for vertical blinds? A cornice board is generally the best because it can be custom-built to exactly cover the headrail’s depth and width. A fabric valance on a rod is easier and cheaper, but it may leave gaps.
Should the valance touch the headrail or sit above it? Ideally, it should sit just above the headrail, covering it completely without touching the blind slats. This prevents interference with the blind’s movement.
Can I install a valance if my blinds are already mounted? Yes, you can install a valance over existing blinds. Just be careful not to damage the headrail when drilling. If the headrail is in the way, you may need to remove the blinds temporarily, but this is rarely necessary.
How do I clean a valance? Fabric valances can usually be vacuumed with a brush attachment or spot-cleaned. Some are machine washable—check the label. Cornice boards should be dusted with a dry cloth.
What if my window is wider than the valance? You can buy a valance that is wider, or use two valances side by side. For cornice boards, you can build one to any width. For fabric valances, you can often order custom sizes.