Metal edging gives your lawn and garden beds a crisp, permanent boundary that keeps grass from creeping into flower beds and mulch from spilling onto the lawn. Unlike plastic or rubber edging, steel or aluminum edging won’t crack, warp, or fade, and it creates a clean, professional look that lasts for years. Installing it is a straightforward weekend project that requires patience and attention to detail, but the payoff is a polished landscape that looks sharp from every angle.
What You’ll Need
- Metal edging strips (steel or aluminum, sold in rolls or straight sections)
- Edging stakes (usually included or purchased separately)
- Rubber mallet or small sledgehammer
- Shovel or half-moon edger
- Garden hose or string and stakes to mark your line
- Tin snips or a hacksaw (for cutting the metal)
- Work gloves (metal edges are sharp)
- Level (optional, for checking the top edge)
- Measuring tape
Step-by-Step
- Plan your line. Lay a garden hose along the desired edge to visualize the curve. Adjust it until you’re happy with the shape. For straight runs, use string stretched between two stakes. Mark the line with spray paint or by scoring the soil with a shovel.
- Dig a trench. Using a sharp shovel or a half-moon edger, cut straight down along your marked line to a depth that matches your edging’s intended burial depth (usually about half the edging height). Then undercut the soil slightly on the lawn side to create a clean vertical wall. The trench should be just wide enough to fit the edging—about the width of the metal strip.
- Set the edging in place. Start at one end. Place the first strip into the trench, with the top edge slightly above the soil level (about a finger’s width). If you’re using a roll, unroll it slowly and let it curve naturally. For straight sections, simply lay them end to end.
- Drive the stakes. Insert a stake through the pre-punched holes or slots on the edging (if your edging doesn’t have holes, you’ll need to drill them). Position the stake on the back side (the garden bed side) so it doesn’t show from the lawn. Drive the stake into the ground with your mallet or hammer until the top of the stake is flush with the top of the edging. Space stakes roughly every couple of feet, and closer on curves.
- Connect the sections. If you have multiple pieces, overlap the ends by a few inches and secure them with a connector piece or by riveting (if supplied). Make sure the top edges are level and aligned.
- Backfill the trench. Once the edging is secured, shovel the displaced soil back into the trench on both sides, packing it firmly with your foot or the handle of your shovel. This locks the edging in place and prevents it from shifting.
- Finish and clean up. Tamp down the soil so it’s slightly below the top edge of the edging. Remove any excess dirt from the lawn. Water the area lightly to settle the soil, then add more soil if needed.
Common Mistakes
- Not digging deep enough. If the trench is too shallow, the edging will sit too high and look awkward, and it may not hold firmly.
- Leaving the top edge uneven. A wavy top edge looks unprofessional. Check with a level or your eye frequently.
- Using too few stakes. Especially on curves, skimping on stakes allows the edging to bow or pop out of the ground.
- Driving stakes at an angle. Stakes should go straight down, not angled, or they’ll loosen over time.
- Cutting the metal with a saw that leaves burrs. Always file or sand down cut edges to avoid injury.
Tips
- Soak the soil with water a day before you dig—it makes cutting through turf much easier.
- For tight curves, make small relief cuts in the bottom flange of the edging (if it has one) to help it bend without kinking.
- Use a rubber mallet to tap the edging down if it sits too high—never hit the metal directly with a steel hammer, as it will dent.
- If your edging has a rolled top edge, keep that edge facing up and toward the lawn for a clean look.
- Consider installing edging before you lay mulch or sod, as it’s much easier to work on bare soil.
Troubleshooting
- The edging won’t stay in the ground. This usually means the trench is too wide or the backfill isn’t packed tightly. Remove the edging, narrow the trench, and reinstall, packing soil firmly on both sides.
- Curves are kinking. Stop and gently bend the metal with your hands (wear gloves) over a wider radius. If it’s already kinked, you may need to cut out the damaged section and splice in a new piece.
- The top edge is wavy. Use a level to find high spots, then tap them down with a rubber mallet. For low spots, lift the edging and add soil underneath before tamping.
- Stakes are bending instead of going in. You’re likely hitting a rock. Move the stake a few inches to the side, or use a metal rod to break up the soil first.
- The edging has popped up after a freeze. This is common in cold climates. Remove the edging, re-dig the trench a bit deeper, and backfill with gravel or sand for better drainage and stability.
Frequently Asked Questions
- How deep should metal edging be buried? Typically, you want to bury about half the edging’s height. For example, if your edging is a few inches tall, bury it so that a couple of inches remain above the soil.
- Can I install metal edging on a slope? Yes, but it’s trickier. You’ll need to step the edging down the slope, overlapping sections slightly, and ensure each section is level. Use extra stakes on the downhill side.
- Will metal edging rust? Steel edging will rust over time, but that’s often a desired aesthetic. If you want to prevent rust, choose powder-coated or galvanized steel, or aluminum, which doesn’t rust.
- How do I cut metal edging? Use tin snips for thin aluminum or steel, or a hacksaw for thicker material. Always wear gloves and eye protection, and file down any sharp edges.
- Can I install metal edging over existing grass? It’s best to remove the grass along the line first. If you install it directly over grass, the grass will likely grow through and undermine the edging.
- How long does metal edging last? With proper installation, steel edging can last for many years, and aluminum can last even longer. The main enemy is frost heave, which can be minimized by good drainage and proper depth.
How to Install Metal Lawn and Landscape Edging