Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

How to Install Pavers Over Concrete Without Mortar

Installing pavers directly over an existing concrete patio is a smart way to refresh an old, cracked, or stained surface without the mess of demolition. This method, often called a “paver overlay,” saves time and money, and it can be done in a weekend with basic tools. The key is to create a stable, level base using sand and polymeric joint sand, which locks the pavers together without any mortar. Before you start, ensure your concrete slab is structurally sound—no large sinking areas or major cracks that indicate movement. If the concrete is in good shape, you can proceed with confidence.

What You’ll Need

  • Concrete cleaner or degreaser
  • Pressure washer or stiff broom
  • Concrete patching compound (for small cracks)
  • Polymeric sand (enough to fill joints and a thin base layer)
  • Paver edge restraints (plastic or aluminum)
  • Rubber mallet
  • Level
  • Straight board (for screeding)
  • Broom (for sweeping sand)
  • Hose with spray nozzle (for activating polymeric sand)
  • Circular saw with masonry blade (for cutting pavers)
  • Safety glasses and dust mask

Step-by-Step

  1. Clean the concrete thoroughly. Remove all dirt, oil, and loose debris. Use a pressure washer for best results, or scrub with a degreaser and rinse. Let the surface dry completely. Any residue can prevent the sand from bonding properly.
  2. Repair any cracks or holes. Fill small cracks and spalled areas with a concrete patching compound. Smooth it flush with the surrounding surface and allow it to cure according to the manufacturer’s instructions. Skip this step if the concrete is in perfect condition.
  3. Check for proper drainage. The concrete should have a slight slope away from your house (about a quarter inch per foot). If water pools anywhere, you may need to add a thin layer of leveling sand to correct it. Use a long level to check.
  4. Install paver edge restraints. Place plastic or aluminum edge restraints around the perimeter of the patio. These keep the pavers from shifting outward over time. Secure them to the concrete with masonry screws or adhesive, following the product instructions.
  5. Spread a thin layer of sand. Pour a layer of coarse sand (not polymeric yet) over the concrete, about a half inch thick. Use a straight board to screed the sand level, using the edge restraints as guides. This layer compensates for minor imperfections and provides a smooth bed.
  6. Lay the pavers. Start from a corner and work your way across. Place each paver firmly into the sand, leaving a small gap (about an eighth of an inch) between pavers. Use a rubber mallet to tap them level, checking with a level frequently. For a herringbone or basketweave pattern, you’ll need to cut pavers at the edges.
  7. Cut pavers as needed. Mark the paver with a pencil or chalk, then score it with a circular saw fitted with a masonry blade. Cut slightly outside the line and then snap the paver along the score. Wear safety glasses and a dust mask.
  8. Fill the joints with polymeric sand. Pour polymeric sand over the entire surface and sweep it into the gaps using a broom. Make sure the joints are completely filled. This sand hardens when wet, locking the pavers together.
  9. Compact and activate. Use a plate compactor (if available) to settle the pavers, then sweep more polymeric sand into any joints that settled. Lightly mist the surface with water using a hose nozzle. Avoid over-watering—you want to moisten the sand, not wash it out. Let it dry for a few hours.
  10. Finish and seal. After the sand has set, sweep off any excess. You can apply a paver sealer to enhance color and protect against stains, but this is optional. Your new patio is ready to use.

Common Mistakes

  • Skipping the concrete repair. If you lay pavers over a cracked slab, the cracks can telegraph through and cause the pavers to shift.
  • Using regular sand instead of polymeric sand. Regular sand washes out and allows weeds to grow. Polymeric sand is essential for a durable, low-maintenance installation.
  • Not installing edge restraints. Without them, the pavers at the edges will slowly spread apart over time.
  • Over-watering the polymeric sand. Too much water can wash the sand out of the joints, leaving gaps. A light mist is all you need.
  • Ignoring drainage. If you create a level surface over a sloped concrete, water will pool. Always maintain a slight slope.

Tips

  • Choose pavers that are at least two inches thick for durability on a patio. Thinner pavers may crack under heavy furniture.
  • Before you start, lay out a few pavers in a dry run to visualize the pattern and spacing.
  • If you don’t have a plate compactor, you can rent one from a local tool rental store. It makes a big difference in settling the pavers evenly.
  • Keep a few extra pavers on hand in case you need to replace one later.
  • Work in small sections when spreading the sand base to avoid disturbing it.

Troubleshooting

Pavers are rocking or uneven. This usually means the sand base is not level. Lift the offending pavers, add or remove sand, and re-level. If the entire area is uneven, you may need to re-screed the sand layer.

Water pools on the surface. If you notice standing water after a rain, you likely have a low spot. Remove the pavers in that area, add a bit more sand to raise the level, and re-lay them. Ensure the slope is consistent.

Polymeric sand is not hardening. This can happen if you over-watered or if the sand was old or damp. You may need to remove the affected sand and replace it with fresh polymeric sand, then mist lightly.

Pavers are shifting at the edges. The edge restraints may not be secure. Check that they are firmly anchored to the concrete. If they are loose, re-screw or add adhesive.

Weeds are growing between pavers. This is a sign that the polymeric sand wasn’t activated properly or that regular sand was used. Remove the weeds and apply a weed killer, then re-sweep polymeric sand into the joints and mist lightly.

Frequently Asked Questions

Can I install pavers over concrete that has a slight slope? Yes, as long as the slope is away from your house and not too steep. You can compensate for minor slopes with a thin sand layer.

Do I need to remove the old concrete? No, that’s the beauty of this method. As long as the concrete is structurally sound, you can overlay it directly.

How long will the paver overlay last? With proper installation and maintenance, it can last for many years. The key is to use quality materials and ensure good drainage.

Can I use any type of paver? Most interlocking concrete pavers work well. Avoid very thin pavers (less than an inch) as they may crack under weight.

Is it necessary to use a plate compactor? It’s highly recommended. It settles the pavers evenly and prevents future shifting. If you don’t have one, you can rent one.

Can I install pavers over painted concrete? Yes, but you must clean the surface thoroughly and ensure the paint is not peeling. If the paint is flaking, it’s best to remove it first.

How to Install Pavers Over Concrete Without Mortar
Scroll to top