Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

How to Jack Up Zero Turn Mowers Safely

Jacking up a zero turn mower is necessary for blade sharpening, deck cleaning, belt replacement, and tire service. Because these mowers are low and heavy, using the wrong lift points or a faulty jack can bend the frame, crush a fuel line, or cause the machine to fall. This guide covers the safe, correct procedure using common garage tools.

What You’ll Need

  • Owner’s manual for your specific model (for lift point locations and weight)
  • Floor jack with a rated capacity above the mower’s weight
  • Jack stands (always use these – never rely on the jack alone)
  • Wheel chocks or blocks of wood
  • Rubber or wooden pads to protect the frame
  • Safety glasses and work gloves

Step-by-Step

  1. Park on a flat, hard surface. Concrete is ideal; avoid grass, gravel, or dirt that can shift. Engage the parking brake and turn the engine off. Remove the key to prevent accidental starting.
  2. Disconnect the spark plug wire(s). This is a safety step that prevents the engine from firing if something is bumped. For twin-cylinder engines, disconnect both wires.
  3. Chock the wheels that stay on the ground. If you’re lifting the front, chock the rear wheels on both sides. If lifting the rear, chock the front wheels. Use solid blocks or chocks.
  4. Consult the owner’s manual for lift points. Most zero turns have reinforced frame rails or designated jacking points. Never place a jack on the deck, transmission, or thin sheet metal.
  5. Position the floor jack under the center of the front or rear lift point. For the front, the typical point is the front axle crossbar or frame crossmember. For the rear, it’s usually the rear frame rails near the wheels. Place a rubber pad or a piece of wood between the jack saddle and the frame to prevent damage.
  6. Pump the jack slowly. Watch the mower as it rises – it should lift evenly. If it starts to tilt or slide, lower it and reposition. Raise it only high enough to do the work (a few inches is usually sufficient for blade access).
  7. Place jack stands under the frame on both sides. Use the correct height and position them on solid frame members, not on the deck or plastic. Lower the mower gently onto the stands so they bear the weight. The jack can remain in place as a secondary support, but the stands are the primary support.
  8. Test stability before working. Give the mower a firm push at the front and rear. If it rocks or moves, lower it and reposition the stands. Only proceed when it’s rock solid.
  9. Do the work. Whether you’re sharpening blades, replacing belts, or changing tires, work calmly and keep tools and parts away from the edges.
  10. Lower the mower. Remove tools and parts from under the deck. Use the jack to raise the mower just enough to remove the stands, then slowly lower it to the ground. Remove the chocks and reconnect the spark plug wires.

Common Mistakes

  • Jacking on the deck. The mower deck is not a structural lift point. It will bend and crack, ruining the deck and possibly dropping the mower.
  • Using only a jack without stands. Jacks can fail or leak. A mower falling on you can cause serious injury. Always use jack stands.
  • Lifting from the center of the rear axle. The transmission or axle housing may not be rated for the full weight. Use the frame rails.
  • Not chocking the opposite wheels. The mower can roll off the jack, especially when lifting the front.
  • Lifting on grass or uneven ground. The jack can sink or tip, causing the mower to fall.

Tips

  • If you don’t have a floor jack, a scissor jack from a car can work, but it’s slower and less stable. Use it only on solid ground and always with stands.
  • For blade sharpening, consider using a block of wood to wedge the blade against the deck to prevent it from spinning – but never put your hand near the blade while the mower is raised.
  • Clean the underside of the deck while it’s up – it’s much easier to access.
  • If you’re lifting the rear, you may need to remove the deck first for better access to the frame. Check the manual.
  • Use a piece of plywood under the jack to distribute the weight if the concrete is cracked or uneven.

Troubleshooting

  • The mower won’t lift evenly. The jack may be off-center. Lower it, reposition, and try again. Also check that the lift point is actually flat – some frames have a curve.
  • The mower slides off the jack. This usually means the jack saddle is not on a flat surface. Use a rubber pad or a piece of wood to create a flat contact point. Also ensure the mower is on level ground.
  • The jack won’t pump up. Check the release valve – it may be slightly open. Close it fully and try again. If it still won’t lift, the jack may be low on fluid or have a leak; use a different jack.
  • The mower rocks on the stands. The stands may be too high or too low, or they’re not on a solid part of the frame. Lower the mower, adjust the stand height, and reposition them on a flat, solid area.
  • You hear a cracking sound as you lift. Stop immediately and lower the mower. You may be lifting on a part that’s not designed to bear weight, like a plastic shroud or a weld that’s weak. Recheck the manual for the correct lift point.

Frequently Asked Questions

Can I use a car jack on my zero turn? Yes, a standard floor jack works, but make sure it has a high enough capacity. Most zero turns weigh between a few hundred and a thousand pounds, so a typical car jack is fine. Use a rubber pad to protect the frame.

Do I need to remove the mower deck to jack it up? Not for the front, but for the rear, the deck can obstruct access to the frame. If you’re lifting the rear, you may need to lower the deck to its lowest setting or remove it entirely to reach a solid lift point.

Is it safe to jack up a zero turn on grass? No. Grass is soft and can compress, causing the jack to sink and the mower to tip. Always use a hard, flat surface like concrete or asphalt.

Where exactly do I place the jack stands? On the frame rails, near the wheels, but not on the axle or the transmission. Look for a flat, solid section of the frame that is designed to support the weight. The owner’s manual will show the exact spots.

Can I change a tire with the mower on jack stands? Yes, but make sure the mower is stable and the stands are rated for the weight. Also, chock the opposite wheels and consider using a wheel chock on the tire you’re not changing.

How high should I lift the mower? Only as high as needed to do the job. For blade access, a few inches is enough. For tire removal, you may need to lift higher, but never so high that the mower becomes unstable. Always use stands.

How to Jack Up Zero Turn Mowers Safely
Scroll to top