Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

How to Protect Tree Saplings from Lawn Mowers

Planting a tree sapling is an investment in your landscape’s future, but a lawn mower can undo that investment in seconds. A single pass with a mower or string trimmer can strip bark, snap the trunk, or kill the young tree outright. This guide shows you practical, low-cost ways to shield your sapling from mower damage while keeping your lawn neat. You’ll learn the best barriers, proper mowing techniques, and how to fix common mistakes.

What You’ll Need

  • Tree guard or trunk protector (plastic spiral, mesh tube, or corrugated pipe)
  • Stakes (wooden or metal) and a mallet or hammer
  • Mulch (wood chips, bark, or shredded leaves)
  • Garden twine or soft ties
  • Scissors or a utility knife
  • Optional: landscape fabric or cardboard

Step-by-Step

  1. Choose the right guard. For young saplings, a rigid plastic spiral guard or a mesh tube works best. These allow air and light while blocking mower blades and string trimmers. Avoid solid, airtight covers that can trap moisture and cause rot.
  2. Install the guard. Wrap the guard around the trunk from the base up to about halfway up the main stem. Ensure it fits snugly but not so tight that it constricts growth. For mesh tubes, push them into the soil slightly to keep them upright.
  3. Stake the sapling (if needed). If the sapling is wobbly or in a windy spot, drive a stake about a hand’s width from the trunk. Use a soft tie (like fabric or rubber) to secure the trunk to the stake. Avoid wire or tight plastic that can girdle the bark.
  4. Create a mulch ring. Spread a layer of mulch around the base, about 2 to 3 inches deep, extending outward to the drip line (the area under the outermost branches). Keep the mulch a few inches away from the trunk to prevent moisture buildup. This ring not only suppresses weeds but also creates a visible buffer zone that reminds you to mow carefully.
  5. Mow in the right direction. Always mow around the sapling with the mower deck tilted away from the tree. Never swing the mower toward the trunk. For string trimmers, hold the head parallel to the ground and avoid direct contact with the guard.
  6. Adjust your mowing pattern. If possible, mow in straight lines that pass by the sapling rather than circling it. This reduces the chance of accidental clipping.
  7. Inspect regularly. Each time you mow, check that the guard is still in place and hasn’t shifted. Look for any nicks or cuts in the bark. Early detection prevents long-term damage.
  8. Remove the guard when the tree matures. Once the trunk is thick enough that mower blades can’t easily damage it (usually when the bark is rough and the tree is several years old), remove the guard to prevent it from constricting growth.

Common Mistakes

  • Using a guard that’s too tight. A guard that presses against the bark can cause girdling, cutting off nutrient flow. Leave a little room for growth.
  • Forgetting to adjust the guard. As the tree grows, the guard can become too short or too snug. Check it a few times a year and replace or reposition as needed.
  • Mowing too close. Even with a guard, mowing within a few inches of the trunk can cause vibration damage. Keep the mower at least a hand’s width away.
  • Using wire or rope to tie the tree. These can cut into the bark. Always use soft, flexible ties and check them for tightness.
  • Skipping the mulch. Mulch not only protects the soil but also makes the sapling area more visible, reducing accidental strikes.

Tips

  • Place a decorative rock or a small fence around the sapling to make it a visual focal point and a physical barrier.
  • If you use a string trimmer, consider using a plastic blade guard on the trimmer head to reduce the chance of slicing the tree.
  • For extra protection, wrap the lower trunk with a commercial tree wrap in addition to a guard. This is especially useful in winter when rodents may also chew.
  • Mow when the grass is dry; wet grass clumps and can pull the guard off.
  • Teach anyone who mows your lawn about the sapling’s location and the importance of avoiding it.

Troubleshooting

The guard keeps falling off. If the guard slips, it may be too large or the tree is too small. Use a smaller guard or secure it with a twist tie at the base. For mesh tubes, push them deeper into the soil.

The bark is already damaged. If the mower has nicked the bark, clean the wound with water and apply a tree wound dressing or pruning sealant (though many experts advise leaving it open to heal naturally). Monitor for signs of disease or pests. If the damage is severe, consult an arborist.

The sapling is leaning. If the tree leans after being hit, gently straighten it and secure it with a stake. Water it well to reduce stress. If the roots are exposed, add soil and mulch.

The guard is causing moisture buildup. If you see mold or rot under the guard, remove it, let the trunk dry, and replace it with a more breathable option like a mesh guard.

The tree is outgrowing the guard. If the trunk is pressing against the guard, remove it immediately and replace with a larger one or none at all if the tree is mature enough.

Frequently Asked Questions

Q: Can I use a plastic bottle as a tree guard?
A: Yes, a cut plastic bottle can work in a pinch, but it’s not ideal. It can trap moisture and heat. Use it only temporarily and replace with a proper guard.

Q: How long should I keep the guard on?
A: Keep it on until the trunk is about the thickness of your thumb or until the bark becomes rough and woody. This usually takes a few years, depending on the tree species.

Q: Will mulch harm my sapling?
A: No, mulch is beneficial if applied correctly. Keep it a few inches away from the trunk to prevent rot and pests. Too much mulch can suffocate roots.

Q: What if I don’t have a guard? What else can I use?
A: You can use a short section of PVC pipe slit lengthwise, or even a wire mesh cylinder. Just make sure it’s open at the top and breathable.

Q: Is it okay to mow right up to the guard?
A: It’s better to leave a small buffer of unmown grass or mulch around the guard. This reduces the chance of the mower catching the guard and pulling it off.

Q: My sapling is in a flower bed. Do I still need a guard?
A: Yes, string trimmers are often used in beds, and they can cause severe damage. A guard is still a good idea until the tree is established.

How to Protect Tree Saplings from Lawn Mowers
Scroll to top