Removing office cubicles is a practical way to open up a floor plan, create a collaborative space, or prepare for a renovation. It involves disassembling the modular panels, work surfaces, and overhead bins, then removing the track or base that anchors them to the floor. Before you start, clear the area around each cubicle, have a plan for where the parts will go, and check whether your building requires a maintenance request or has specific rules about debris disposal. You’ll also want at least one other person to help, as panels are heavy and awkward to carry.
What You’ll Need
- Power drill with Phillips and flathead bits (cordless is easiest)
- Allen wrench set (many cubicle brands use hex bolts)
- Screwdrivers (both Phillips and flathead)
- Rubber mallet (for tapping apart stubborn connections)
- Pry bar or putty knife (for lifting base tracks)
- Utility knife (to cut caulk or adhesive if present)
- Work gloves and safety glasses
- Furniture dolly or hand truck (for moving panels)
- Zip ties or rope (to bundle loose parts)
- Drop cloths or cardboard (to protect floors and stack parts)
Step-by-Step
- Clear the work area. Remove all personal items, paperwork, and electronics from the cubicle. Unplug any power strips or data cables and label them with tape so you know where they go later. If the cubicle has a phone or monitor arm, detach those first.
- Remove the work surface (desk top). Look underneath the desk top for brackets or clips that attach it to the panels. Most are held by a few screws or bolts. Use your drill or Allen wrench to remove them, then lift the desk top straight up and off. Set it aside on a soft surface to avoid scratches.
- Take down overhead cabinets and shelves. If your cubicle has an overhead storage bin, open the door and remove any contents. Locate the screws or bolts on the underside or sides that secure the cabinet to the panel tops. Have a partner support the cabinet while you remove the fasteners, then lower it carefully.
- Remove the panels one at a time. Panels are connected with clips, brackets, or interlocking edges. Start at one end of the cubicle and work your way around. Look for a small release lever or a screw at the top and bottom of each panel joint. If panels are connected with hex bolts, use the Allen wrench. Once detached, tilt the panel slightly and lift it off its base or track. Have your partner help you carry it to the staging area.
- Disconnect the power and data connections. Many cubicles have a power beam or data port integrated into the panel. These are usually plugged into a floor outlet or a junction box. Unplug them carefully and coil the cords. If the system is hardwired, you may need to turn off the circuit at the breaker and call an electrician to disconnect it safely.
- Remove the base track or floor anchors. After all panels are down, you’ll see a metal track or small brackets screwed into the floor. Use a pry bar or putty knife to lift the track if it’s glued down. For screws, use your drill to remove them. Be careful not to damage the flooring underneath—if the track is stuck, use a utility knife to cut any caulk or adhesive first.
- Clean up and dispose of parts. Sort the hardware into labeled bags (screws, bolts, clips) and bundle panels together with zip ties. If you plan to reuse the cubicle, store the parts in a dry area. If not, check with your building management or local waste service about disposal—many parts are recyclable metal or plastic.
Common Mistakes
- Not labeling parts. If you’re planning to reassemble the cubicle elsewhere, failing to label which panel goes where or which screws belong to which joint makes reassembly a nightmare.
- Removing panels out of order. Trying to take out a middle panel before the end ones can stress the structure and make it harder to detach.
- Forgetting to disconnect power. Pulling a panel while it’s still wired to a live outlet can cause sparks or damage. Always unplug or disconnect first.
- Lifting heavy panels alone. Panels are bulky and can weigh more than you expect. Lifting by yourself risks injury and damage.
- Damaging the floor. Prying up a base track without cutting adhesive can gouge carpet or tile. Take your time and use a putty knife.
Tips
- Take photos before you start—especially of the connections—so you have a reference if you need to put it back.
- Use a furniture dolly to move panels; they’re easier to stack and roll than to carry.
- Work in pairs: one person to hold the panel steady, the other to remove fasteners.
- Check the manufacturer’s logo or model number on the panels. Many brands have online manuals that show the exact disassembly steps.
- If the cubicle is older, the screws may be stripped or rusted. Spray a little penetrating oil on stubborn bolts and wait a few minutes before trying again.
Troubleshooting
Panels are stuck together. If panels won’t separate, check for hidden screws or clips—sometimes there’s a small access hole on the side. Tap the joint gently with a rubber mallet to break the seal. If it’s still stuck, look for a locking key or a release button that you might have missed.
Screws won’t budge. Stripped or rusted screws are common. Use a larger screwdriver bit or a screw extractor. If that fails, drill out the screw head with a metal drill bit (careful not to damage the panel).
Base track is glued to the floor. Slide a putty knife under the track and work it along the length to break the adhesive. If the glue is stubborn, use a heat gun on low to soften it—but be cautious with carpet or vinyl.
Power beam is hardwired. If you can’t unplug the power, stop and call a licensed electrician. Do not attempt to cut wires while the circuit is live. Turn off the breaker and have the electrician disconnect the junction box safely.
You’re missing a tool. Many cubicle systems use a standard Allen wrench, but some use a Torx or star driver. Check the bolt heads before you start and borrow or buy the correct bit—using the wrong size will strip it.
Frequently Asked Questions
Can I remove a cubicle without damaging it? Yes, if you follow the steps carefully and avoid prying on panels. Most modular cubicles are designed to be disassembled and reassembled. The main risk is bending clips or scratching surfaces, so use the right tools and work gently.
Do I need to remove the carpet or floor track? The base track is usually left in place if you plan to reinstall the cubicle. If you’re removing it permanently, you’ll need to pull up the track and patch any holes in the floor. That’s a separate job that may require a flooring professional.
How long does it take to remove one cubicle? With two people and the right tools, a standard cubicle can be taken down in a couple of hours. Larger or more complex setups with overhead bins and power beams may take longer.
What should I do with the old cubicle parts? If they’re in good shape, you can sell them or donate to a local nonprofit. Otherwise, check with your waste management service—many accept metal and plastic for recycling. Some office furniture companies offer take-back programs.
Can I remove a cubicle by myself? Technically yes, but it’s not recommended. Panels are heavy and hard to handle alone. You risk injury and damage. At minimum, have a partner help with lifting and carrying.
Do I need to turn off the power before removing a cubicle? Yes, if the cubicle has integrated power. Unplug any cords first, and if the power is hardwired, turn off the circuit breaker and have an electrician disconnect it. Never work on live electrical components.