Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

How to Replace a Broken Tile: Step-by-Step Guide

Replacing a broken tile can seem like a big job, but with the right tools and a careful approach, you can make it look like it never happened. This guide walks you through the entire process, from removing the damaged tile to installing a new one and finishing the grout. Before you start, make sure you have a replacement tile that matches the existing ones. If you have leftover tiles from the original installation, great. If not, you may need to take a sample to a tile store to find a close match. You will also want to protect the surrounding area and have all your tools ready.

What You’ll Need

  • Replacement tile (matching the original as closely as possible)
  • Safety glasses and work gloves
  • Hammer and a cold chisel (or a rotary tool with a tile bit)
  • Putty knife or scraper
  • Vacuum cleaner (to clean out debris)
  • Tile adhesive (thin-set mortar or mastic, appropriate for your tile type)
  • Notched trowel (sized for your tile)
  • Grout (matching the existing grout color) and a grout float
  • Grout sponge and a bucket of clean water
  • Small piece of wood or a block (to protect the tile when tapping)
  • Spacers (if needed, to keep the tile aligned)
  • Rags for cleanup

Step-by-Step

  1. Prepare the area. Clear the area around the broken tile. Lay down a drop cloth to catch debris and protect the floor. Put on your safety glasses and gloves.
  2. Break the damaged tile. Use the hammer and cold chisel to break the tile into smaller pieces. Start in the center of the tile and work outward. Be careful not to damage the surrounding tiles. If you have a rotary tool, you can also drill a series of holes in the tile to make it easier to break.
  3. Remove the broken pieces. Carefully lift out the large pieces of the tile. Use a putty knife or scraper to remove any remaining bits of tile and the old adhesive from the substrate. The goal is to get down to a clean, flat surface.
  4. Clean the opening. Vacuum out all dust and debris from the hole. Wipe the area with a damp rag to remove any remaining dust. The surface needs to be clean for the new adhesive to bond properly.
  5. Test fit the new tile. Place the new tile into the opening to check the fit. It should sit level with the surrounding tiles. If it is too high, you may need to remove some of the old adhesive. If it is too low, you will need to apply a thicker layer of new adhesive.
  6. Apply the adhesive. Using the notched trowel, spread a layer of tile adhesive on the back of the new tile. You want enough to cover the back completely, but not so much that it oozes out excessively when you press it down. The notches in the trowel will create ridges that help the adhesive bond.
  7. Set the tile. Carefully place the tile into the opening. Press it down firmly and wiggle it slightly to set it into the adhesive. Use the wood block and a hammer to gently tap the tile until it is level with the surrounding tiles. If you have tile spacers, you can use them to keep the gap even.
  8. Clean off excess adhesive. Wipe away any adhesive that squeezes out from the edges with a damp rag. It is much easier to clean it now than after it dries.
  9. Let the adhesive cure. Follow the manufacturer’s instructions for the adhesive you are using. Most thin-set mortars need at least a few hours to cure, but it is best to wait overnight before grouting.
  10. Apply the grout. Once the adhesive is fully cured, mix your grout according to the package directions. Using a grout float, press the grout into the gaps around the new tile. Work it in at an angle to ensure the gaps are completely filled.
  11. Wipe off excess grout. After letting the grout set for a few minutes, use a damp sponge to wipe away the excess grout from the surface of the tile. Rinse the sponge frequently and be careful not to dig the grout out of the joints. Let the grout dry.
  12. Buff the tile. Once the grout is dry, use a clean, dry rag to buff away any remaining haze on the tile surface. Your new tile should now blend in with the surrounding ones.

Common Mistakes

  • Not protecting the surrounding tiles. When breaking the old tile, it is easy to chip the neighboring tiles. Use a cold chisel and work carefully, or tape over the adjacent tiles for extra protection.
  • Removing too much adhesive. If you scrape down to the substrate, you may end up with a hole that is too deep, making the new tile sit lower than the rest. Remove only the loose adhesive and leave a solid base.
  • Using the wrong adhesive. Not all adhesives work for all tile types. For example, some mastics are not suitable for large-format tiles or for wet areas. Always check the label to ensure it is appropriate for your tile and location.
  • Skipping the test fit. Failing to test fit the tile can lead to a tile that is too high or too low. Always check the fit before applying adhesive.
  • Grouting too soon. If you grout before the adhesive is fully cured, the tile may shift. Follow the curing time recommended by the adhesive manufacturer.

Tips

  • If you do not have a replacement tile, consider taking a broken piece to a tile store to match the color and size. Tiles can vary slightly between batches, so finding an exact match may be challenging.
  • To make the new tile blend in better, you can mix a small amount of paint or stain into the grout to match the existing grout color.
  • When removing the old tile, try to keep the substrate intact. If you damage the underlying backer board, you will need to repair that first.
  • Work in a well-ventilated area, especially when using adhesives and grout, as they can emit fumes.
  • If you are replacing a tile in a shower or other wet area, consider applying a waterproofing membrane over the substrate before setting the new tile.

Troubleshooting

The new tile is higher than the surrounding tiles. This usually means there is too much adhesive. Remove the tile, scrape away some of the adhesive, and try again. You can also press down harder when setting the tile.

The new tile is lower than the surrounding tiles. This means you removed too much of the old adhesive. You can apply a thicker layer of new adhesive, or you can build up the area with a patching compound before setting the tile.

The new tile cracks when you try to set it. This can happen if the substrate is uneven or if you tap too hard. Make sure the surface is smooth and use a gentle tapping motion with the wood block.

The grout color does not match. If you cannot find an exact match, you can use a grout colorant or stain to tint the new grout. Apply it after the grout has dried and cured.

The tile does not stick. If the tile does not adhere, the adhesive may have dried out before you set the tile, or the surface may have been dusty. Remove the tile, clean the area, and apply fresh adhesive.

Frequently Asked Questions

Can I replace a tile without removing the grout around it? It is best to remove the grout around the broken tile first, as this makes it easier to break and remove the tile without damaging the neighbors.

How long does the adhesive need to dry before grouting? It depends on the adhesive. Most thin-set mortars require at least a few hours, but it is safest to wait overnight. Always check the manufacturer’s instructions.

What if I don’t have a replacement tile? You can try to find a matching tile at a home improvement store or a tile specialty shop. Bring a sample or a photo. If you cannot find an exact match, you may need to replace a larger section or use a contrasting tile as a design feature.

Can I use caulk instead of grout for the new tile? Caulk is more flexible than grout and is often used in corners and where the tile meets the tub or sink. For the joints between tiles, grout is the standard choice, but you can use caulk if you prefer a flexible seal.

Why does my new tile look slightly different from the others? Tiles can vary in shade between batches. If the difference is noticeable, you can try to blend it in by using a grout color that matches the surrounding grout, or you can swap the tile with one from a less visible area.

Do I need to seal the grout after it dries? Sealing grout is recommended, especially in wet areas, to prevent stains and moisture damage. Apply a grout sealer after the grout has fully cured, following the sealer’s instructions.

How to Replace a Broken Tile: Step-by-Step Guide
Scroll to top