Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

Replace Sliding Glass Doors with French Doors

Replacing a sliding glass door with French doors changes both the look and the function of a room. French doors open fully, letting in more light and making it easier to move large furniture or step out onto a patio. The project involves removing the old door unit, adjusting the rough opening, and installing a new pre-hung door. It is a demanding job that requires two people and a full day, plus basic carpentry and framing skills. Before starting, confirm that the new French door unit fits the existing opening or plan to reframe it. Check local building codes for egress and safety glass requirements, and have a helper ready for lifting.

What You’ll Need

  • Pre-hung French door unit (with or without a center mullion)
  • Shims (cedar or plastic)
  • Level (at least a standard 2-foot level, longer is better)
  • Pry bar and hammer
  • Cordless drill with screwdriver bits
  • Deck screws or door frame screws (long enough to reach the studs)
  • Wood shims for the sill and sides
  • Expanding foam insulation (low-expansion type)
  • Caulk and caulk gun
  • Utility knife
  • Reciprocating saw (for removing old frame and cutting nails)
  • Safety glasses, work gloves, and dust mask
  • Weather barrier tape or flashing tape
  • Optional: circular saw for trimming rough opening studs

Step-by-Step

  1. Measure the rough opening. Remove the interior trim around the sliding door to expose the wood framing. Measure the width and height of the opening from stud to stud and from the subfloor or sill to the header. Write these numbers down. Compare them to the manufacturer’s rough opening requirements for your chosen French door. If the opening is too small, you will need to enlarge it; if too large, you will add shims or new studs.
  2. Remove the sliding glass door panels. Start by taking out the sliding panel. Lift it slightly and tilt the bottom toward you, then lift it out of the bottom track. Set it aside carefully. Next, remove the fixed panel by lifting it up and out of the top track, then tilting the bottom out. Have a helper hold the glass; these panels are heavy and fragile.
  3. Remove the old door frame and track. Use a pry bar and hammer to carefully pull off the interior trim. Then, cut through any nails or screws holding the frame to the studs with a reciprocating saw. Pry the frame away from the studs, working from top to bottom. Remove the metal track and the threshold. You may need to cut the frame into manageable pieces with a saw. Dispose of the old materials.
  4. Inspect and prepare the rough opening. Check the exposed studs, sill, and header for rot, water damage, or insect damage. Replace any damaged wood. Ensure the opening is plumb and square. If the opening is not square, you have two options: shim the new door to fit, or cut the studs to make it square. For most homes, shimming is sufficient. If you need to widen the opening, cut the studs with a reciprocating saw and install a new header and king studs. This is a structural step; if you are unsure, consult a contractor.
  5. Install weather barrier tape. Apply self-adhesive flashing tape to the sill and the sides of the rough opening. This prevents water from seeping in. Overlap the tape so water runs outward, not inward. Press it firmly around the entire perimeter.
  6. Set the new French door in place. With a helper, carry the pre-hung French door unit to the opening. Tilt it in from the outside, bottom first. Set the bottom on the sill, then tilt the top into place. Center the door in the opening. Check that the door is level across the sill and plumb on the hinge side. Use a level to verify.
  7. Shim and fasten the frame. Insert wood shims between the door frame and the studs. Start at the bottom corners, then work up the hinge side. Place shims at each hinge location. Check that the door is still plumb. Drive screws through the frame and shims into the studs. Do not overtighten, as this can bow the frame. Use long screws for the hinge side to support the weight of the doors.
  8. Check the door operation. Open and close both doors. The gap between the doors and the frame should be even. If the door rubs, loosen the screws slightly and adjust the shims. Re-tighten. The doors should swing freely and latch without force.
  9. Install the center mullion (if applicable). Some French doors have a removable center post that allows both doors to open fully. If your unit has one, insert it into the frame and secure it according to the manufacturer’s instructions. This piece adds stability and ensures the doors seal properly.
  10. Insulate and seal the gaps. Remove any excess shims with a utility knife. Fill the gaps between the frame and the studs with low-expansion foam. Spray a thin bead, then let it expand. Do not overfill, as it can push the frame out of alignment. After the foam dries, trim it flush with a knife.
  11. Reinstall trim and hardware. Nail the interior trim back into place. On the exterior, apply a bead of exterior caulk around the frame where it meets the siding. Install the door handles, locks, and any additional hardware. Adjust the strike plates so the latch engages smoothly.
  12. Final adjustments. Check the weatherstripping for gaps. Adjust the hinges if the door sags. Clean the glass and test the locks. Walk away and come back to ensure the doors still operate smoothly after settling.

Common Mistakes

  • Skipping the square and plumb check. Installing a door in a crooked opening causes binding and air leaks. Always verify with a level before fastening.
  • Over-tightening screws. This warps the frame and makes the door stick. Screws should be snug, not torqued down.
  • Using too much foam. Expanding foam can bow the frame if it fills the gap completely. Use a thin line and allow room for expansion.
  • Forgetting the weather barrier. Without flashing tape, water can seep into the wall and cause rot over time.
  • Not having a helper. Lifting a heavy door unit alone can damage the door or injure your back. Always use two people.
  • Ignoring egress requirements. If this is a bedroom, the opening must meet local fire code for escape. Check before buying the door.

Tips

  • Order the door with the rough opening size in hand, not the other way around. Most manufacturers list exact rough opening dimensions.
  • Use shims in pairs, one from each side, to keep the frame straight.
  • Place a piece of plywood over the opening at night to secure your home during the project.
  • If the old sliding door track is set in concrete, use a masonry blade on your saw to cut it out.
  • Apply a coat of exterior paint or sealant to the cut ends of the studs before installing the new door.
  • Keep the door unit in the house for a day before installation so the wood can acclimate to the humidity.

Troubleshooting

  • Door will not close evenly. Loosen the screws on the hinge side and add or remove shims to adjust the plumb. Re-tighten slowly, checking the gap as you go.
  • Water leaks at the bottom. Check the sill slope. The exterior side should be lower than the interior. If not, add a sill pan or adjust the flashing. Re-caulk the bottom corners.
  • Door sags after a few months. This usually means the hinge screws are not long enough to reach the studs. Replace the short screws with longer ones that bite into the framing.
  • Air drafts around the frame. The foam may have gaps. Spray additional low-expansion foam into the voids, or use backer rod and caulk for small cracks.
  • Glass fogs between panes. This indicates a broken seal in the insulated glass. If under warranty, contact the manufacturer. Otherwise, the glass unit will need replacement.
  • Door sticks to the frame in humid weather. Sand the high spots on the door edge or the frame, then repaint or seal. Also check that the hinges are not loose.

Frequently Asked Questions

Can I install French doors in the same opening as my sliding door? Often yes, but the opening may need adjustment. Sliding doors are typically wider than standard French doors, so you may need to add framing to narrow the opening, or choose a wider French door unit.

Do French doors save energy compared to sliding doors? Modern French doors with double-pane glass and good weatherstripping are comparable to sliding doors. The main difference is the seal at the center, which can leak if not adjusted properly.

Can I do this project alone? It is not recommended. The door unit is heavy and awkward to lift. You risk injury or damage to the door. At minimum, have a helper for the lifting and setting steps.

How long does the replacement take? For a typical homeowner, plan on a full day. Removing the old door and preparing the opening takes a few hours, and installation and finishing take the rest of the day.

Do I need a building permit? Many jurisdictions require a permit for exterior door replacement because it affects egress and energy efficiency. Check with your local building department before starting.

What if my opening is not level? You can shim the door to level it, but the sill must be sloped slightly outward for drainage. If the floor is severely unlevel, you may need to adjust the subfloor or use a custom-sized door.

Replace Sliding Glass Doors with French Doors
Scroll to top