Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

How to Take Cuttings from Bedding Plants

Taking cuttings from bedding plants is a simple way to create many new plants from just a few, saving money and preserving your favorite varieties. This guide walks you through the process, from choosing the right stems to potting up your new plants.

What You’ll Need

  • A healthy, well-watered parent plant (not in flower)
  • Clean, sharp scissors or pruning shears
  • Small pots or seed trays with drainage holes
  • Fresh, free-draining potting mix (a mix of multi-purpose compost and perlite or vermiculite works well)
  • A clear plastic bag or a propagator lid to create humidity
  • Watering can with a fine rose
  • Optional: rooting hormone powder or gel

Step-by-Step

  1. Prepare your pots. Fill your pots or trays with the potting mix, firm it down gently, and water it well. Let the excess water drain before you insert the cuttings.
  2. Choose the right stems. In the morning, when the plant is fully hydrated, look for non-flowering side shoots. These should be healthy, firm, and about two to three inches long. Avoid stems that are too soft and floppy or too woody and tough.
  3. Make the cut. Using your clean scissors or shears, cut the stem just below a leaf node (the point where a leaf joins the stem). This is where roots are most likely to form. Make a clean, angled cut.
  4. Trim the cutting. Remove the lower leaves from the bottom half of the cutting, leaving just two or three leaves at the top. If the remaining leaves are large, you can cut them in half to reduce water loss.
  5. Apply rooting hormone (optional). Dip the cut end of the stem into rooting hormone powder or gel. Tap off any excess. This step is not essential, but it can speed up rooting and improve success rates, especially for harder-to-root plants.
  6. Insert the cuttings. Make a small hole in the potting mix with a pencil or your finger. Gently insert the cutting so that the leafless part of the stem is buried. Firm the mix around the base of the cutting. Space multiple cuttings a couple of inches apart in a tray, or put one or two in a small pot.
  7. Water and cover. Water the cuttings gently with a fine rose to settle the soil around them. Place the pots in a propagator or cover them with a clear plastic bag. You can support the bag with small sticks to keep it from touching the leaves.
  8. Provide the right conditions. Place the cuttings in a warm, bright spot out of direct sunlight. A windowsill with bright, indirect light is ideal. The goal is to keep them warm and humid but not in scorching sun.
  9. Monitor and wait. Check the cuttings every few days. Remove any fallen leaves or any cutting that looks moldy. Keep the potting mix lightly moist but not waterlogged. Condensation inside the bag is normal and good.
  10. Pot on. After a few weeks, gently tug on a cutting. If you feel resistance, roots have formed. At this point, you can gradually open the bag or turn off the propagator for longer periods each day to harden off the new plants. After a week of this, pot them up individually into small pots with standard potting mix.

Common Mistakes

  • Taking cuttings from flowering stems. The plant’s energy goes into making flowers, not roots. Always choose non-flowering shoots.
  • Letting cuttings dry out. Once cut, a stem loses water quickly. Prepare your pots before you cut, and if you are taking many cuttings, keep the ones you have already cut in a plastic bag or between damp paper towels.
  • Using dirty tools. Dirty scissors can introduce disease. Wipe blades with rubbing alcohol before you start.
  • Overwatering. Too much water leads to rot. The potting mix should be moist, not soaking wet. Good drainage is crucial.
  • Putting cuttings in direct sun. Direct sunlight will cook the cuttings inside their plastic cover. Bright, indirect light is what they need.

Tips

  • Take more cuttings than you think you need. Not every one will root, so having extras ensures you end up with enough plants.
  • Take cuttings in the morning when the plant is full of water. This reduces stress on the cutting.
  • Use a pencil to make holes in the potting mix. This prevents the cutting’s stem from being scraped and damaged when you push it in.
  • If you do not have a propagator, a clear plastic bottle with the bottom cut off can work as a mini greenhouse.
  • Keep a label in each pot with the plant name and the date you took the cutting. It is easy to forget which is which.
  • For very soft-stemmed bedding plants like begonias or fuchsias, you can even root cuttings in a glass of water on a bright windowsill, then pot them up once roots appear.

Troubleshooting

Cuttings are wilting. This usually means they are losing water faster than they can take it up. Increase humidity by covering them more securely, and make sure they are out of direct sunlight. Trim off any severely wilted leaves.

Mold or rot at the base. This is caused by too much moisture and poor air circulation. Remove the affected cuttings immediately, and let the remaining ones dry out a bit. Open the bag or propagator vents for a few hours each day to increase airflow.

No roots after several weeks. Some plants simply take longer than others. Check that the cuttings are still firm and green. If they are, give them more time. If they have turned black or mushy, they have rotted and should be discarded.

Leaves turning yellow. This can be a sign of overwatering or nutrient deficiency. Check that the potting mix is not waterlogged. Do not feed cuttings until they have rooted.

Cuttings have rooted but are growing leggy. This means they are not getting enough light. Move them to a brighter spot, but still out of direct sun, and pinch out the growing tip to encourage bushier growth.

Frequently Asked Questions

When is the best time to take cuttings? Spring and early summer are ideal for most bedding plants, as the parent plants are in vigorous growth. You can take them later in the season, but they may take longer to root.

Can I take cuttings from any bedding plant? Most soft-stemmed bedding plants root easily from cuttings, including geraniums, fuchsias, coleus, and petunias. Some, like impatiens, are also very easy. A few, such as those grown from seed for specific traits, may not come true from cuttings, but for most common bedding plants, it works well.

Do I need rooting hormone? No, it is not strictly necessary. Many soft-stemmed cuttings will root perfectly well without it. However, it can speed up the process and improve success rates, particularly for plants that are a bit more stubborn.

How long does it take for cuttings to root? This varies by plant and conditions. Some quick-rooting plants like coleus may show roots in about a week, while others like geraniums might take a few weeks. You will know they have rooted when you feel resistance to a gentle tug.

Should I pinch out the growing tip? Yes, once the cutting has rooted and started to grow, pinching out the top pair of leaves encourages the plant to branch out and become bushier, which gives you a better plant for the garden.

Can I plant the cuttings straight into the garden? It is not recommended. The young roots are delicate and need protection. It is much safer to pot them up and grow them on in a sheltered spot for a few weeks before planting out, after they have been hardened off.

How to Take Cuttings from Bedding Plants
Scroll to top