Ripping a board means cutting it lengthwise, with the grain, to make it narrower. A table saw is the fastest and most accurate tool for this job, but it is also one of the most dangerous tools in a workshop. This guide walks you through the safe, correct way to rip boards on a table saw, from setup to finishing the cut. Before you start, make sure the saw is unplugged while you adjust anything, and that you have a clear workspace with no tripping hazards.
What You’ll Need
- Table saw with a sharp, properly aligned blade (a combination or rip blade works best)
- Push sticks or a push block (at least one, preferably two)
- Safety glasses and hearing protection
- Dust mask or shop vacuum (optional but recommended)
- Straight, flat boards that are free of nails, staples, and loose knots
- A tape measure and a combination square
- A riving knife or splitter (if your saw has one, use it)
- Featherboards or a push paddle (helpful for long or thin cuts)
Step-by-Step
- Inspect the board. Look down the length of the board for warps, bows, or twists. Check both faces and edges for embedded metal, loose knots, or cracks. A board that is not flat or has defects can bind or kick back. If the board is badly warped, do not rip it until you have jointed one edge flat.
- Set the blade height. Unplug the saw. Raise the blade so it protrudes about one tooth’s height above the top of the board you are cutting. A blade that is too high is more dangerous; one that is too low can cause burning or rough cuts. Roughly, the blade should be about a quarter inch above the material for most boards.
- Install and adjust the riving knife or splitter. If your saw has one, ensure it is in place and aligned with the blade. The riving knife prevents the kerf from closing and pinching the blade, which is a primary cause of kickback. If your saw does not have one, consider using a splitter or a zero-clearance insert with a splitter.
- Set the fence. Measure the distance from the fence to the blade’s teeth that are tilted toward the fence. Use a tape measure or a combination square to set the fence to the desired width of the finished piece. Lock the fence securely. Double-check the measurement at both the front and back of the blade to ensure the fence is parallel to the blade.
- Check the fence for clearance. The fence should be positioned so the offcut (the waste piece) falls freely to the outside of the blade. Never trap the waste between the fence and the blade. If you are ripping a narrow piece, the fence should be on the side of the blade where the waste is wider.
- Adjust the anti-kickback pawls. If your saw has pawls (small toothed devices that ride on the wood), make sure they are set so they barely touch the surface of the board. They should grab the wood if it tries to move backward.
- Put on safety gear. Wear safety glasses and hearing protection. Tie back long hair, remove jewelry, and roll up loose sleeves. Do not wear gloves while operating the saw.
- Position your body. Stand to the left of the blade (if the fence is on the right) or to the right (if the fence is on the left). Your body should be slightly to the side, not directly in line with the blade. Keep your feet shoulder-width apart and stable.
- Start the saw and let it come to full speed. Wait until the blade is at maximum RPM before feeding the board. A slow blade can grab and kick back.
- Feed the board. Place the board flat on the table, with one edge firmly against the fence. Use your dominant hand to push the board forward, keeping it pressed against the fence. Use your other hand to hold the board down flat against the table, but keep it well away from the blade. Do not reach over the blade.
- Use push sticks near the blade. As your hands get within about a foot of the blade, switch to a push stick. Use one push stick to keep the board against the fence and another to push it forward. Never let your fingers get closer than a few inches to the blade.
- Maintain steady pressure. Push the board through at a steady, moderate pace. Do not force it. If the motor bogs down, slow your feed. If you hear the blade whining or the wood burning, you are feeding too fast or the blade is dull.
- Finish the cut. When the board passes the blade, continue pushing with the push stick until the cut is complete and the board is clear of the blade. Do not reach for the board until the blade has stopped spinning or you have used a push stick to move it away.
- Turn off the saw. After the cut is complete, turn off the saw and wait for the blade to come to a complete stop before removing any scraps or adjusting anything.
Common Mistakes
- Ripping without a riving knife or splitter. This is the most common cause of kickback. The kerf can close and pinch the blade, throwing the board back at you.
- Standing directly in line with the blade. If kickback happens, the board flies straight back. Stand to the side to avoid being in its path.
- Using your hands too close to the blade. Many people rely on their fingers for too long. Use push sticks from the moment your hands are within a foot of the blade.
- Feeding too fast. This causes burning, rough cuts, and can overload the motor. Let the saw do the work.
- Removing the guard. The blade guard protects you from accidental contact. Remove it only for special operations like dado cuts, and reinstall it immediately after.
- Ripping a board that is not flat. A cupped or twisted board can rock and bind. Joint one face and one edge first, or use a sled.
Tips
- Use a featherboard. A featherboard clamped to the table presses the board against the fence, keeping the cut straight and freeing your hands for pushing.
- Make a zero-clearance insert. This reduces tear-out and supports the wood right at the blade, giving a cleaner cut.
- For very thin rips (less than an inch wide), use a push block with a lip that hooks over the board, or use a sacrificial push stick that is taller than the blade. Never try to rip a thin piece with your fingers.
- Keep the table clean and waxed. A slick surface makes feeding easier and reduces the chance of the board catching.
- Use a sharp blade. A dull blade burns the wood and pushes harder, increasing the risk of kickback. Replace or sharpen blades regularly.
- Plan your cut. Always rip the board so the waste piece is on the outside of the blade, not trapped between the fence and blade. This prevents the waste from binding.
Troubleshooting
- The board binds or the saw stalls. Stop immediately. Turn off the saw and unplug it. Check if the fence is parallel to the blade. Check if the board has internal stress (it may have been cut from a curved tree). If the board is pinching the blade, remove it carefully and consider jointing the edge or using a different board.
- The cut is not straight. The fence may be misaligned with the blade. Check the fence with a square against the miter slots. Also check that the blade is parallel to the miter slots. Adjust if needed.
- The wood burns or leaves a rough edge. The blade is likely dull or the feed rate is too slow. Try feeding faster. If it still burns, the blade needs sharpening or replacement. Also check that the blade is not warped.
- Kickback occurs. This is a serious event. If a board is thrown back, stop the saw immediately. Do not try to catch the board. Inspect the saw for damage. Re-evaluate your setup: is the riving knife in place? Is the fence parallel? Did you feed too fast? Often, kickback happens when the waste piece is trapped between the fence and blade, so always position the fence so the waste is on the outside.
- The offcut is wider than the piece you wanted. Your fence measurement was off. Always measure from the fence to the blade’s teeth that are closest to the fence. Re-measure and adjust.
- The board drifts away from the fence. The board may have a bow or the fence may be too far from the blade, causing the board to flex. Use a featherboard to hold it against the fence, and ensure the board is flat.
Frequently Asked Questions
- Do I need a riving knife? Yes, absolutely. A riving knife prevents kickback by keeping the kerf open. If your saw does not have one, install a splitter or use a table saw with one. It is a critical safety feature.
- Can I rip a board that is longer than the table? Yes, but you need support. Use roller stands or a work surface at the same height as the saw table on both the infeed and outfeed sides. The board must not sag or tip.
- What is the narrowest piece I can safely rip? It depends on your push stick design. If you have a push stick that is taller than the blade and a zero-clearance insert, you can rip very thin strips. But never use your fingers to guide a piece that is narrower than your hand. Use a push block or a dedicated thin-rip jig.
- Should I wear gloves? No. Gloves can catch on the blade and pull your hand in. Always keep bare hands, but use push sticks to keep them away from the blade.
- Why does my blade leave burn marks? Burn marks are usually caused by a dull blade, feeding too slowly, or a blade that is not aligned with the miter slots. Try sharpening the blade, increasing feed speed, or checking alignment.
- Can I rip plywood on a table saw? Yes, but plywood is large and can be unwieldy. Use a sharp blade with many teeth (a crosscut or combination blade) to reduce tear-out. Support the sheet well, and consider using a helper or an outfeed table. Also, check for voids in the plywood that could cause the cut to wander.
How to Use a Table Saw Safely for Ripping Boards