Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

Installing Bathroom Sink Plumbing: 10 Steps

This listicle walks you through the complete process of installing bathroom sink plumbing, from the supply lines to the drain trap. It is written for confident DIYers who have basic tool skills and want to avoid calling a plumber for a straightforward job. You will learn the correct order of work, the specific parts you need, and the common mistakes that cause leaks or slow drains.

1. Turn Off the Water and Disconnect Old Lines

Before anything else, close the shutoff valves under the sink—usually two small valves on the wall or floor. If there are no valves, turn off the main water supply for the house. Then use an adjustable wrench to loosen the compression nuts on the supply lines; have a bucket and rag ready because a little water will spill from the lines even after the valves are closed.

2. Remove the Old Drain and Trap

The P-trap is the curved pipe under the sink; it holds water to block sewer gases. Unscrew the slip nuts on both ends of the trap and pull it off, then remove the tailpiece that drops from the sink strainer. If the nuts are stuck, use penetrating oil and a pair of channel-lock pliers, but be careful not to crush the pipe.

3. Clean and Inspect the Sink Opening

Once the old drain is out, scrape away old putty or plumber’s sealant from the sink flange area. Check the sink’s drain hole for cracks or corrosion—if the sink is porcelain, a chipped edge can cause leaks. Wipe the surface dry with a clean cloth so the new sealant adheres properly.

4. Install the New Drain Assembly

Most bathroom sinks use a pop-up drain assembly. Apply a thin bead of plumber’s putty around the underside of the flange, then insert it into the sink hole. From below, slide the rubber gasket and friction washer onto the threaded tailpiece, then hand-tighten the locknut. Wipe away excess putty that squeezes out around the flange.

5. Attach the Tailpiece and P-Trap

The tailpiece is the straight pipe that connects the drain flange to the trap. Slide the slip nut and washer onto the tailpiece, then push it into the trap’s inlet. Hand-tighten the slip nut first, then snug it with a wrench—but do not overtighten, as that can crack the plastic. The trap should angle slightly downward toward the wall drain.

6. Connect the Trap to the Wall Drain

The trap’s outlet slips into a pipe stub coming out of the wall. Measure the distance and cut the trap arm to length with a hacksaw if needed. Slide the slip nut and washer onto the trap arm, insert it into the wall stub, and tighten. Ensure the trap has a slight slope so water flows freely, not pooling in the curve.

7. Install the Supply Lines

Use flexible braided stainless steel supply lines—they are easier to route than rigid copper and less likely to kink. Connect one end to the shutoff valve and the other to the sink’s hot and cold inlets. Hand-tighten the nuts, then give them a quarter turn with a wrench. Do not use Teflon tape on compression fittings; the threads seal with the ferrule, not tape.

8. Attach the Pop-Up Rod and Linkage

For a pop-up drain, the lift rod on the faucet connects to a horizontal linkage that raises the stopper. Insert the rod through the faucet body and attach the clevis strap, then adjust the pivot ball so the stopper opens and closes fully. Test it by pushing the rod down—the stopper should seal when closed and lift freely when open.

9. Turn On the Water and Check for Leaks

Slowly open the shutoff valves and let water run into the sink. Check every connection—supply lines, drain flange, trap nuts—with a dry paper towel. Tighten any dripping nut slightly, but if a compression fitting leaks after a gentle snug, disassemble and check that the ferrule is seated correctly. Run the water for a full minute to confirm no slow leaks appear.

10. Test the Drain Flow and Seal

Fill the sink basin halfway, then pull the stopper and let it drain. Watch for water pooling around the flange or a gurgling sound from the trap, which indicates a venting problem. Also check the trap’s water seal by looking for a steady water level in the curve—if it drains out completely, the trap is not holding water, and you need to adjust the trap arm angle.

How to Choose

When picking parts, match the drain opening size—most bathroom sinks are a standard size, but some vessel sinks use a different tailpiece. For supply lines, measure the distance between the shutoff valve and the sink inlet; braided stainless lines come in several lengths, so buy one that is close without being overly long. For the trap, choose plastic (PVC or ABS) for ease of cutting and fitting, or chrome-plated brass for a cleaner look, but brass is harder to cut and more expensive. Always buy a drain assembly that includes the pop-up linkage if your faucet has a lift rod, because separate parts may not align.

Frequently Asked Questions

Do I need plumber’s putty or silicone for the drain flange? Plumber’s putty works for most sinks, but silicone sealant is better for stone or quartz since putty can stain. Apply a thin bead and wipe away excess immediately.

Why does my drain leak only when the sink is full? That usually means the flange seal is failing, or the locknut under the sink is loose. Remove the drain, clean off old putty, and reinstall with fresh sealant.

Can I reuse the old supply lines? Yes, if they are in good shape and the nuts are not corroded, but new braided lines are cheap and more reliable. Reusing old lines risks cracks that only show under pressure.

What if the trap doesn’t line up with the wall drain? You can cut the trap arm shorter or use an extension tube. The trap arm should slope slightly down toward the wall, so adjust the length until it fits without forcing.

Is Teflon tape needed on any of these connections? Only on threaded pipe joints, like the faucet’s tailpiece to the supply line if it uses threads. Compression fittings and slip nuts do not need tape—they seal with a washer or ferrule.

Final Thoughts

Installing bathroom sink plumbing is a manageable weekend project if you work methodically and check for leaks at each step. The most common mistakes are overtightening plastic nuts, forgetting the rubber washers, and not sloping the trap correctly. Take your time, keep a bucket and rags handy, and test thoroughly before you close up the cabinet.

Installing Bathroom Sink Plumbing: 10 Steps
Scroll to top