Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

Palomar Knot Tutorial: 10 Steps to a Perfect Tie

This guide walks you through the palomar knot, one of the strongest and most reliable fishing knots you can learn. Whether you’re a beginner spooling a new reel or an experienced angler looking to refine your technique, these ten steps cover everything from setup to common mistakes. By the end, you’ll tie a palomar that holds firm under pressure, every time.

Step 1: Double the Line

Start by folding about six inches of your fishing line back on itself to create a loop. This doubled section is what gives the palomar its strength—it distributes the load across two strands instead of one. Make sure the loop is large enough to pass over your lure or hook easily, but not so big that it becomes unwieldy.

Step 2: Pass Through the Eye

Thread the loop through the eye of your hook, lure, or swivel. Unlike some knots that require the tag end to go through, here you pass the entire loop. This step is straightforward, but ensure the line doesn’t twist as you pull it through—twists can weaken the finished knot.

Step 3: Tie an Overhand Knot

With the loop still through the eye, tie a simple overhand knot using the doubled line. The hook should be hanging in the middle of the loop, not off to one side. This is the foundation of the palomar, so keep it loose for now—you’ll tighten it later.

Step 4: Loop Over the Terminal Tackle

Now, take the loop you created and pass it completely over the hook, lure, or swivel. This is the signature move of the palomar. If you’re using a lure with multiple treble hooks, be careful not to snag the line on a hook point—this is a common frustration.

Step 5: Moisten the Line

Before you pull the knot tight, wet the line with saliva or a drop of water. This reduces friction heat, which can weaken monofilament or fluorocarbon lines. It also helps the knot slide smoothly into place, ensuring a snug, even seat.

Step 6: Pull the Tag End and Standing Line

Hold the tag end (the short piece) and the standing line (the long piece) in separate hands, and pull them in opposite directions. The knot will slide down toward the eye. Pull steadily, not with a jerk, to avoid damaging the line. You should see the overhand knot cinch down neatly.

Step 7: Trim the Tag End

Once the knot is tight, clip the tag end close to the knot—about an eighth of an inch is ideal. Leaving it longer can cause the knot to catch on weeds or rocks, while cutting too short risks the knot slipping. Use sharp scissors or a line cutter for a clean cut.

Step 8: Test the Knot

Give the knot a firm tug to test its strength. A properly tied palomar won’t slip or break at the knot—if it fails, it’s usually due to a mistake in earlier steps. This quick test saves you from losing a fish later. If it slips, retie it; never fish with a suspect knot.

Step 9: Practice with Different Lines

The palomar works with braided, monofilament, and fluorocarbon lines, but each behaves slightly differently. Braid is stiff and can be harder to cinch, while mono is more forgiving. Practice with the line you plan to use, so you know how much tension to apply.

Step 10: Avoid Common Mistakes

The most frequent errors are passing the loop over the hook before tying the overhand knot, and forgetting to moisten the line. Another is pulling the tag end instead of the standing line, which can leave the knot loose. Watch for these and you’ll tie a perfect palomar every time.

How to Choose

When deciding whether the palomar is right for a given situation, consider the line type and the size of the terminal tackle. It’s excellent for braided lines because it doesn’t slip, but it can be bulky on very small hooks or flies. For heavy saltwater gear, the palomar is a top choice; for tiny trout lures, a clinch knot might be more practical. The palomar also uses more line than other knots, so if you’re low on line, a simpler knot may be better.

Frequently Asked Questions

Q: Can I tie the palomar with a swivel?
A: Yes, the palomar works well with swivels, snaps, and most terminal tackle that has an eye. Just ensure the loop is big enough to pass over the entire swivel.

Q: Does the palomar work with fluorocarbon?
A: It does, but fluorocarbon is stiffer and more brittle than mono. Moisten it thoroughly and pull slowly to avoid heat damage.

Q: Why does my palomar slip?
A: Slipping usually means the overhand knot wasn’t tied correctly, or the tag end wasn’t trimmed close enough. Retie and double-check your steps.

Q: Is the palomar stronger than a clinch knot?
A: In most tests, the palomar retains more of the line’s breaking strength than a clinch knot, which is why it’s favored for heavy cover and big fish.

Q: Can I tie the palomar with a lure that has multiple hooks?
A: Yes, but be careful. The loop must pass over all the hooks, so use a larger loop to avoid tangling.

Q: How long does it take to learn?
A: Most people get it after a few tries. Practice with a thick rope or cord first to see the structure clearly, then switch to your fishing line.

Final Thoughts

The palomar knot is a skill worth mastering—it’s strong, simple, and versatile. Once you’ve tied it a few times, it becomes second nature, and you’ll trust it in situations where other knots fail. Keep practicing, and you’ll never hesitate to retie on the water.

Palomar Knot Tutorial: 10 Steps to a Perfect Tie
Scroll to top