Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

How to Install Brick Around a Window: Step-by-Step

Installing brick around a window gives your home a classic, solid look and can also protect the window frame from weather. This guide walks you through the process for a standard window with a brick ledge or rough opening. You’ll need basic masonry skills, but with careful planning, it’s a manageable weekend project. Before you start, check your local building codes—some areas require flashing or specific clearances around windows. Also, confirm the brick you choose matches the existing wall or the style you want.

What You’ll Need

  • Bricks (enough to cover the area, plus a few extra for cuts)
  • Mortar mix (type S or N, depending on your climate)
  • Masonry trowel
  • Level (at least 2 feet long)
  • Mason’s line and line blocks
  • Brick hammer or masonry saw for cutting
  • Joint tool (for striking the mortar joints)
  • Bucket and water for mixing
  • Hawk or mortar board
  • Safety glasses and gloves
  • Flashing (if required by code)
  • Weep holes (small tubes or wicks)

Step-by-Step

  1. Prepare the area. Clean the window frame and the surrounding wall. Remove any old caulk or debris. If there’s a brick ledge, make sure it’s level. If not, you may need to build a temporary support or use angle iron to carry the brick above the window.
  2. Install flashing (if needed). Place a piece of metal or plastic flashing over the top of the window frame, extending up the wall a few inches and out over the frame. This directs water away from the window. Secure it with roofing nails or adhesive.
  3. Set up a level line. Snap a chalk line or use a mason’s line to mark the bottom course of brick. This will be your guide for the first row. If the window sits on a ledge, start there; otherwise, start a few inches below the sill.
  4. Mix mortar. Follow the bag instructions. You want a consistency like peanut butter—not too wet, not too dry. Mix only as much as you can use in about an hour.
  5. Butter the bricks. Using your trowel, spread a layer of mortar on the bottom of the brick (for the first course) and on one end. Press the brick into place, using the level to keep it flat and aligned with the line. Tap gently with the trowel handle to adjust.
  6. Lay the first course. Work from one side of the window to the other. Keep the joints consistent—about 3/8 inch is typical. Use a spacer or your trowel handle to gauge. Check level after every few bricks.
  7. Build up the sides. Continue laying courses up the sides of the window. Stagger the vertical joints—each brick should overlap the one below by at least a quarter of its length. Use a level to keep the wall plumb (vertically straight).
  8. Cut bricks to fit. When you reach the top of the window, you’ll likely need to cut bricks to fit the remaining space. Use a brick hammer and chisel, or a masonry saw. Measure twice, cut once.
  9. Lay the header course. The bricks above the window should be laid on a steel angle or lintel that spans the opening. Butter the bricks and set them on the angle, ensuring they overlap the side bricks. This course ties the wall together.
  10. Install weep holes. Every few bricks along the bottom course, leave a small gap or insert a plastic tube to allow water to escape. This prevents moisture buildup behind the brick.
  11. Finish the joints. Once the mortar is thumb-print hard (after a few hours), use a joint tool to press the mortar into a smooth, concave shape. This helps shed water. Brush off excess with a stiff brush.
  12. Clean up. Remove any mortar smudges from the brick faces with a damp cloth before it dries. Let the mortar cure for a few days—keep it slightly damp by misting with water if the weather is hot and dry.

Common Mistakes

  • Not using flashing above the window—this leads to water leaks.
  • Laying bricks without a level line, resulting in a crooked wall.
  • Making mortar too wet or too dry, which weakens the bond.
  • Forgetting weep holes, causing trapped moisture and mold.
  • Cutting bricks with a hammer and chisel without safety glasses—always wear protection.
  • Rushing the job and not letting mortar cure properly before applying weight.

Tips

  • Work in the shade if possible; hot sun dries mortar too fast.
  • Use a story pole—a straight board marked with course heights—to keep vertical spacing consistent.
  • If you’re a beginner, practice on a small patch first.
  • Keep a bucket of clean water nearby to rinse tools.
  • For a perfect match, use brick from the same batch or blend from several pallets.

Troubleshooting

  • Bricks are slipping out of place. Mortar is too wet. Remix with less water, and let the first course set before adding more.
  • Mortar is too hard to tool. You waited too long. Mist the joints with water to soften, or skip tooling and just brush.
  • Wall is leaning. Check your level every course. If it’s off, you may need to remove and re-lay the affected bricks before the mortar sets.
  • Bricks won’t fit at the top. Measure the gap and cut bricks to size. Sometimes you need to adjust the joint thickness slightly.
  • Water is pooling on the sill. Ensure the sill bricks have a slight downward slope away from the window.

Frequently Asked Questions

Do I need to use a special type of mortar?

Type S mortar is strong and good for most exterior applications. Type N is softer and more flexible, suitable for above-grade walls. Check with your local supplier for the best match.

Can I install brick directly against the window frame?

No, you should leave a small gap (about 1/4 inch) and fill it with caulk or backer rod to allow for expansion and prevent cracking.

How long does the mortar take to dry?

Mortar typically sets in a few hours, but it takes several days to cure fully. Keep it moist for at least a couple of days for maximum strength.

What if my window is too wide for a single lintel?

For wider openings, you may need a reinforced lintel or a steel angle with additional support. Consult a structural engineer for spans beyond a few feet.

Can I use thin brick veneer instead of full brick?

Yes, thin brick is lighter and easier to install, but it’s not structural. It’s a good option if you don’t need the brick to support weight.

Do I need to seal the brick after installation?

Sealing is optional. It can protect against staining, but it also traps moisture. If you do seal, use a breathable masonry sealer.

How to Install Brick Around a Window: Step-by-Step
Scroll to top