Mets Minor League Blog

Music theory, instruments and musicians

Mets Minor League Blog

Music theory, instruments and musicians

How to Install a Shower Stall Inside the Wall

Installing a shower stall directly into the wall framing gives your bathroom a built-in, seamless look and eliminates the gap between the shower pan and the wall. This guide covers a pre-fabricated, one-piece or three-piece shower unit set into the stud cavity, not a custom tile job. Before you start, confirm the wall is not load-bearing, and that you have access to the plumbing supply and drain lines from behind or below. You will also need to check local building codes for pan liner requirements and venting.

What You’ll Need

  • Shower stall unit (one-piece or three-piece, sized to fit your rough opening)
  • Pressure-treated lumber for the curb and any new framing
  • Shower pan liner or pre-formed pan (if not part of the unit)
  • Cement board or waterproof backer board
  • Thin-set mortar and tile (if tiling the walls) or the unit’s own wall panels
  • Plumbing: shower valve, shower head arm, drain assembly, P-trap, and pipe fittings
  • Waterproof membrane or sealant tape for seams
  • Screws, nails, shims, and a level
  • Saw (reciprocating or circular), drill, and utility knife
  • Pipe wrench, plumber’s tape, and a basin wrench
  • Safety gear: gloves, eye protection, and a dust mask

Step-by-Step

  1. Turn off the water supply at the main shut-off valve. Open a faucet elsewhere to drain the lines. Confirm the water is off before cutting into any pipe.
  2. Remove the existing wall surface (drywall or plaster) from the studs in the area where the shower will sit. Cut the opening so it extends a few inches beyond the planned shower footprint on each side, and from the floor up to at least a foot above the shower head height.
  3. Inspect the studs for rot, warping, or damage. Replace any compromised studs with new lumber of the same size. Use a level to check that the studs are plumb and the floor is level; shim or plane as needed.
  4. Frame the shower opening. If the unit is wider than the existing stud spacing, add new studs to create a rough opening that matches the unit’s dimensions. For a curbless shower, the floor must slope toward the drain, so you may need to build a sloped subfloor with mortar.
  5. Rough in the plumbing. Run the hot and cold supply lines to the valve location, and the shower head pipe up the wall. Install the drain pipe and P-trap so the drain stub-out is centered and at the correct height for the shower pan. Leave the pipes capped and pressure-test them if possible.
  6. Install the shower pan or base. If using a separate pan, set it on a bed of thin-set mortar so it is fully supported and level. Press it down evenly, then check with a level. Let the mortar cure for the time specified on the bag.
  7. Set the wall panels or backer board. For a one-piece unit, lift it into place and slide it into the framed opening, making sure the flanges overlap the pan. For a three-piece unit, install the back panel first, then the side panels, following the manufacturer’s interlocking system. Screw the flanges into the studs, but do not over-tighten.
  8. Waterproof all seams. Apply a waterproof membrane or sealant tape over every joint where panels meet the pan and where panels meet each other. Use a roller to press out air bubbles. Pay extra attention to corners and the valve opening.
  9. Install the shower valve and head. Connect the supply lines to the valve body, then mount the valve to the wall using the bracket provided. Screw the shower head arm into the elbow at the top of the pipe, and hand-tighten, then give it a quarter turn with a wrench. Wrap plumber’s tape on all threaded connections.
  10. Connect the drain. Attach the drain flange to the pan’s drain hole, and connect the tailpiece to the P-trap. Tighten the slip nuts by hand, then a half-turn with a wrench. Do not use a wrench to over-tighten plastic fittings.
  11. Finish the wall surfaces. If you used cement board, apply thin-set and tile, then grout and seal. If the unit has its own panels, install the trim pieces or bullnose edges. Leave a small gap (about the width of a coin) between the shower unit and the surrounding drywall, and fill it with silicone caulk.
  12. Test the shower. Turn the water back on slowly. Check for leaks at every joint, especially the valve, shower head, and drain. Run the water for a few minutes, then inspect the area behind the shower (if accessible) and the ceiling below for any moisture.

Common Mistakes

  • Not checking for level before setting the pan. A pan that is off-level by even a small amount will cause water to pool and not drain properly.
  • Skipping the waterproofing membrane on seams. Even if the panels are labeled waterproof, the seams are the weak points where leaks happen.
  • Over-tightening drain fittings. Plastic threads strip easily, and a cracked fitting will leak behind the wall where you cannot see it.
  • Forgetting to account for wall thickness. If the shower unit is designed for a standard wall, adding extra backer board or tile can make the flange sit proud of the finished wall.
  • Not supporting the pan fully. A pan that is not bedded in mortar can flex and crack the drain seal or the pan itself.

Tips

  • Dry-fit the entire unit before applying any adhesive or mortar. This lets you see if the rough opening is too small or if the plumbing stub-outs are in the wrong place.
  • Use a stud finder to locate all studs before cutting, and mark them on the floor so you know where to screw later.
  • Apply a bead of silicone caulk to the underside of the pan flange before setting the walls, creating a gasket that prevents water from wicking up behind the panels.
  • Keep the protective film on the shower unit’s surface until the very end to avoid scratches from tools.
  • Have a helper for lifting the unit. Most shower stalls are awkward and heavy, and a second pair of hands prevents damage and injury.

Troubleshooting

Water leaks at the drain. Turn off the water, disassemble the drain fittings, and check that the rubber gasket is seated correctly. Replace any cracked parts and re-tighten gently. If the leak is from the pan itself, the pan may be cracked—this usually requires replacing the pan.

Water seeps out from under the curb. The curb is not sealed properly. Apply a generous bead of silicone along the inside and outside of the curb where it meets the floor. If the curb is built from lumber, you may need to install a metal curb liner before tiling.

The shower head drips after turning off. This is usually a worn washer or O-ring inside the valve. Replace the cartridge or the washer, following the valve manufacturer’s instructions.

The wall panels bow inward. The studs are not plumb or the flanges were not screwed into the studs securely. Remove the screws, add shims behind the flanges to push the panel outward, and re-screw.

Mold appears on the ceiling below. There is a slow leak in the drain or supply lines. Turn off the water and open the ceiling to inspect. Look for wet insulation or water stains on the subfloor. Fix the leak before closing the ceiling.

Frequently Asked Questions

Can I install a shower stall without removing the drywall? No. The unit must be set into the stud cavity, so you need to expose the framing. You can cut the drywall to the exact size of the unit, but you will still need to remove it.

Do I need a building permit? Most localities require a permit for any work that involves plumbing or altering a wet area. Check with your local building department before starting. Failing to get a permit can cause issues when selling the home.

How long does the mortar bed need to cure before I can use the shower? Follow the mortar manufacturer’s instructions, but typically it is safe to walk on the pan after a day, and to run water after a few days. For tile, wait at least a day before grouting, and a few more days before sealing.

Can I use drywall instead of cement board behind the shower? No. Standard drywall will absorb moisture and deteriorate. Use cement board, fiber-cement board, or a waterproof foam board specifically rated for wet areas.

What if my floor is not level? You must level the floor before setting the pan. Use a self-leveling compound on a concrete subfloor, or shim the pan and fill the gap with mortar. A pan that is not level will not drain correctly.

Is it okay to use a one-piece unit instead of a three-piece? Yes, a one-piece unit has fewer seams, so it is less likely to leak. However, it is much harder to maneuver through doorways and into the framed opening. Measure your access path carefully before purchasing.

How to Install a Shower Stall Inside the Wall
Scroll to top